NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 527
Outgoing Trunk Queuing O-2
Service Conditions (cont’d)
13. If a user goes on-hook within 6-8 seconds after encountering all trunks busy, OUTGOING TRUNK
QUEUING can be set automatically to the station.
14. The station is set for OGQ for a minimum of 30 seconds to one hour, maximum. This time is adjustable
through the System Data base. After this time, OGQ will be cancelled automatically.
15. ACCOUNT CODE [A-18] and FORCED ACCOUNT CODE...

NEAX2400 IMX Feature Programming Manual
Page 528ND-70184 (E), Issue 3
O-2 Outgoing Trunk Queuing
Programming (cont’d)
(RAM data of 3C [Hex] provides for 30 minutes). 
System Data 2, Index 4, Bit 0. Should the access code for CALL BACK and OGQ be the same? 0/1:
No/Yes. Usually assign data “1”. Assign on a per-tenant basis. 
System Data 2, Index 4, Bit 1. Enable Automatic OGQ? 0/1: No/Yes. Assign on a per-tenant basis.
Automatic operation eliminates the need to access via dial pad.
System Data 2, Index 4,...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 529
Outgoing Trunk Queuing O-2
FCCS Programming (cont’d)
STEP 3:ANPDN - These data must be assigned to the NCN.
TN: Tenant
1st DC: 1st Digit
CI: Normal (N), Hooking (H) and Busy (B)
NND: Number of Necessary Digits
BLF: Busy Lamp Field
STEP 4:ARTDN - These data must be assigned to the NCN.
LGRT: Logical Route Number
Assign CDN 9:TQ, Trunk Queuing Service = 1
Note 1:
When using ASYDL or ASYDN to program an FCCS feature, the basic...

NEAX2400 IMX Feature Programming Manual
Page 530ND-70184 (E), Issue 3
O-2D Outgoing Trunk Queuing - Dterm
O-2D Outgoing Trunk Queuing - Dterm
General Description
This service allows a Dterm user, upon encountering a trunk busy signal, to enter a first-in, first-out queue.
Operating Procedure
Without LEAST COST ROUTING - 3/6-DIGIT [L-5]: 
1. Dial the trunk access code; receive busy tone.
2. Press the CALL BACK key, receive service set tone. The LCD displays:
3. Replace the handset.
4. When the trunk...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 531
Outgoing Trunk Queuing - DtermO-2D
Service Conditions (cont’d)
4. Individual stations may only initiate one OUTGOING TRUNK QUEUE - Dterm at a time. Subsequent
attempts will produce a reorder tone.
5. Stations may be restricted from use of this feature via CLASS OF SERVICE - INDIVIDUAL [C-15].
6. The station is put in queuing condition for a maximum of 30 seconds to one hour (adjustable through
system data). After this timing, OG...

NEAX2400 IMX Feature Programming Manual
Page 532ND-70184 (E), Issue 3
O-2D Outgoing Trunk Queuing - Dterm
Interactions
1. Dial pad operation for Dterm sets may be exercised. A FLASH BUTTON [F-3D] must be programmed to
a programmable line/feature key.
2. OGQ-AUTOMATIC may operate with either same or separate access codes. If the Automatic option is
chosen, service set tone will be sent when encountering an all trunks busy situation. No dial pad operation
will be required.
3. When testing OGQ, at least one...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 533
Outgoing Trunk Queuing - DtermO-2D
FCCS Programming (cont’d)
System Data 1, Index 41:Designate the Trunk Queuing Override Timer
Index 68, b3: Enables automatic cancel timer
0/1: -/Automatic cancel timer is Available
Index 159: Designate Automatic Cancel Timer
STEP 2:ASPAN - These data must be assigned to the NCN.
TN: Tenant Number
ACC: Access number
CI: B = Busy (for Entry), N = Normal (for Cancel)
SRV: SSC
SID: 19 = OG Queuing-Entry...

NEAX2400 IMX Feature Programming Manual
Page 534ND-70184 (E), Issue 3
O-6 Off-Hook Alarm
O-6 Off-Hook Alarm
General Description
This feature allows a user to call the Attendant or a predetermined station by simply staying OFF-HOOK. The
calling number is automatically displayed at the ATTENDANT CONSOLE [A-3] or a Dterm series with a display.
Operating Procedure
1. Lift the handset and stay off-hook.
2. After a predetermined time elapses (2 to 30 sec.), the call will terminate at the ATTENDANT CONSOLE...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 535
Off-Hook Alarm O-6
Service Conditions (cont’d)
13. If a station belongs to the node that has an Attendant Console, the station is connected with the Attendant
Console. If a station belongs to the node that does not have an Attendant Console, the station is connected
with the specified Attendant Console in the remote node according to the system data assigned. See the
figure below.
Interactions
1. A total of seven OFF-HOOK ALARM Groups...

NEAX2400 IMX Feature Programming Manual
Page 536ND-70184 (E), Issue 3
O-6 Off-Hook Alarm
Programming (cont’d)
S: Station
A: Attendant Console
SSTN: Special Station Number
STEP 3:ASGD - This command defines what stations belong to the Special Incoming Group. Assign the
following: 
TN: Tenant Number 
STN: Station Number 
F: Function Number (0-7)
0: Off-Hook Alarm 
GN: Group Number (1-7)
STEP 4:ASFC - Assign a Service Feature Class that allows SFI 30 to stations that will have OFF-HOOK
ALARM. 
STEP 5:AAKP -...