NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 487
Message Waiting Lamp Setting - Station M-30
Service Conditions (cont’d)
7. The LCD on the Dterm Series E station displays the following messages:
Interactions
1. For MESSAGE WAITING LAMP SETTING-STATION, the 8DLC/16ELC card is required.
2. An external power source is required to light a single line telephone lamp. The nondisplay  D
terms use an
80 VDC power source. NEC stocks Lorain Model HSA3H.
3. The use of the following features...

NEAX2400 IMX Feature Programming Manual
Page 488ND-70184 (E), Issue 3
M-30 Message Waiting Lamp Setting - Station
Interactions (cont’d)
4. When an incoming call is answered by the sub-line appearance on another station, the following services
may be activated either by the answering station or by another station towards the answering station. These
services will not interfere with the answering station’s ability to leave a Message Waiting indication. 
PRIVACY-D
term[P-14D]
CONSULTATION HOLD-ALL CALLS...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 489
Multiple Call Forwarding - All Calls M-44
M-44  Multiple Call Forwarding - All Calls
General Description
This feature permits a call to a CALL FORWARDING - ALL CALLS station to be forwarded multiple times to a
predesignated idle station.
Operating Procedure
To set MULTIPLE CALL FORWARDING - ALL CALLS [C-5] from an individual station:
1. Lift the handset; receive dial tone. 
2. Dial the specific CALL FORWARDING - ALL CALLS access code;...

NEAX2400 IMX Feature Programming Manual
Page 490ND-70184 (E), Issue 3
M-44 Multiple Call Forwarding - All Calls
Service Conditions (cont’d)
c.) If a sequence of CALL FORWARDING - ALL CALLS [C-5] and CALL FORWARDING -
BUSY LINE [C-2] forwards the call back to the originating station, the forward is not made and
the caller hears a busy tone.
d.) If a sequence of CALL FORWARDING - ALL CALLS [C-5] and CALL FORWARDING -
BUSY LINE [C-2] forwards the call back to the originally called station, and if that...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 491
Multiple Call Forwarding - All Calls M-44
Service Conditions (cont’d)
b.) The Attendant Console key that lights when a call is forwarded to the console depends on the
forwarding status of the originally called station (except in paragraph c). The following table
shows the key that will light; e.g., the BUSY key will light, if the forwarding status of the
originally called station is CALL FORWARDING - BUSY LINE [C-2], and the call is...

NEAX2400 IMX Feature Programming Manual
Page 492ND-70184 (E), Issue 3
M-44 Multiple Call Forwarding - All Calls
Service Conditions (cont’d)
b.) If a call is forwarded by CALL FORWARDING - BUSY LINE [C-2] to stations that are
members of hunting groups, a hunting check is performed on the busy line closest to the called
station, or on the busy line closest to the final forward destination. In the diagram below, a
hunting check is performed on Hunt Groups 1 or 4. A hunting check is never performed on
Groups...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 493
Multiple Call Forwarding - All Calls M-44
Interactions (cont’d)
4. When a station in a STATION HUNTING [S-7, 8, 9] group initiates MULTIPLE CALL FORWARDING-
ALL CALLS, calls normally destined for this station will not be received. The hunt group operates as if
the station were busy. 
5. A noncontrolling UCD station is allowed to activate CALL FORWARDING [C-5]. With this station call
forwarded, only calls dialed directly to this...

NEAX2400 IMX Feature Programming Manual
Page 494ND-70184 (E), Issue 3
M-44 Multiple Call Forwarding - All Calls
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node. 
(Note)
STEP 1:ASYDN - These data must be set to the NCN.
System Data 1 Index 69,...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 495
Manual Signaling M-47
M-47 Manual Signaling
General Description
This feature permits Dterm users to send a one-second ring to a predetermined station. The manual intercom SIGNAL
key (SIG key) is operational at all times. An Intercom call is not required. If the signalled station is ringing from
another call, the manual intercom signal will interrupt that ringing.
Operating Procedure
Press the SIG key; send a one-second ring to the...

NEAX2400 IMX Feature Programming Manual
Page 496ND-70184 (E), Issue 3
M-47 Manual Signaling
Programming (cont’d)
TP: Type of Dterm 0/1:
RING:
0: No Ringing
1: Ringing All Lines 
2: Ringing on Prime Line Only
3: Flexible Ring Assignment, enables RG parameter. 
PRI: Form of Line Preference (0-3)
KYN: Key Number (1-40)
KYI: Service Index
0: Key Not Used
1: Feature Key 
2: Multi-line Key
KD: Kind of Line
0: Multi-line
1: Intercom Line 
ICM: Kind of Intercom
0: Automatic Intercom
1: Manual Intercom 
2: Dial...