NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 467
Multiple Call Forwarding - Busy Line M-24
Operating Procedure (cont’d)
5. Dial the desired target telephone number; receive service set tone.
To cancel CALL FORWARDING - BUSY LINE [C-2] from the ATTENDANT CONSOLE [A-3]: 
1. Press an idle loop key. 
2. Dial the CALL FORWARDING - BUSY LINE [C-2] cancel code; receive special dial tone.
3. Dial the TENANT [T-12] number (2 or 3 digits).
4. Dial the originating telephone number; receive...

NEAX2400 IMX Feature Programming Manual
Page 468ND-70184 (E), Issue 3
M-24 Multiple Call Forwarding - Busy Line
Service Conditions (cont’d)
e.) If a forwarding destination is the originally called station, and if the originally called station
forwarded the call with CALL FORWARDING - BUSY LINE, the ultimate destination is the
originally called station.
f.) If the call is forwarded to a station where it has previously been forwarded to, the call will end at
that station.
6. CALL FORWARDING - ALL CALLS...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 469
Multiple Call Forwarding - Busy Line M-24
Service Conditions (cont’d)
b.) The Attendant Console key that lights when a call is forwarded to the console depends on the
forwarding status of the originally called station. The following table shows the key that will light
(if the forwarding status of the originally called station is CALL FORWARDING - BUSY [C-2],
and the call is from a station, then the BUSY key will light).
c.) If the...

NEAX2400 IMX Feature Programming Manual
Page 470ND-70184 (E), Issue 3
M-24 Multiple Call Forwarding - Busy Line
Service Conditions (cont’d)
11. Busy Services such as EXECUTIVE OVERRIDE [E-1], CALL BACK [C-1], etc.:
a.) Busy service is provided to the busy line closest to the originally called station.
12. DIT, NIGHT CONNECTION - FIXED [N-1]:
a.) For CALL FORWARDING - ALL CALLS [C-5] and CALL FORWARDING - BUSY LINE [C-
2], a forward check is made up to 5 times by System Data.
b.) In DIRECT-IN TERMINATION...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 471
Multiple Call Forwarding - Busy Line M-24
Interactions (cont’d)
5. If an Attendant attempts BUSY VERIFICATION [B-3] to Station A, which has CALL FORWARDING-
BUSY LINE [C-2] set to Station B and Station B is busy, BUSY VERIFICATION [B-3] proceeds against
Station B. If Station A has set CALL FORWARDING-BUSY LINE [C-2] to the Attendant Console,
BUSY VERIFICATION [B-3] is allowed at Station A, if Station A is busy.
6. When CALL...

NEAX2400 IMX Feature Programming Manual
Page 472ND-70184 (E), Issue 3
M-24 Multiple Call Forwarding - Busy Line
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node. 
(Note)
STEP 1:ASYDN - These data must be set to the NCN.
System Data 1, Index69,...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 473
Multiple Call Forwarding - Don’t Answer M-25
M-25 Multiple Call Forwarding - Don’t Answer
General Description
This feature permits a call to an unanswered station to be forwarded, multiple times, to preprogrammed idle stations
that do not have Call Forwarding set.
Operating Procedure
To set CALL FORWARDING - DONT ANSWER [C-3] from an individual station: 
1. Lift the handset; receive dial tone.
2. Dial the specific CALL FORWARDING -...

NEAX2400 IMX Feature Programming Manual
Page 474ND-70184 (E), Issue 3
M-25 Multiple Call Forwarding - Don’t Answer
Service Conditions (cont’d)
d.) If the forwarding sequence, after a CALL FORWARDING - DONT ANSWER [C-3] goes
through several stations with CALL FORWARDING - ALL CALLS [C-5] set and ends up at the
original CALL FORWARDING - DONT ANSWER [C-3] station, CALL FORWARDING -
DONT ANSWER [C-3] is not activated.
e.) If the forwarding sequence, after a CALL FORWARDING - DONT ANSWER [C-3] goes
through...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 475
Multiple Call Forwarding - Don’t Answer M-25
Service Conditions (cont’d)
b.) The Attendant Console key that lights when a call is forwarded to the console depends on the
forwarding status of the originally called station (except in case c). The following table shows the
key that will light (e.g., if the forwarding status of the originally called station is CALL
FORWARDING - BUSY LINE [C-2], and the call is from a station, then the...

NEAX2400 IMX Feature Programming Manual
Page 476ND-70184 (E), Issue 3
M-25 Multiple Call Forwarding - Don’t Answer
Interactions (cont’d)
2. Any UCD station is allowed to activate CALL FORWARDING-DON’T ANSWER [C-3]. When this
station sets CALL FORWARDING-DON’T ANSWER [C-3], calls directed to this station through UCD
hunting or directly-dialed will ring and then follow the destination of the CALL FORWARDING-DON’T
ANSWER [C-3].
3. CALL FORWARDING-DON’T ANSWER [C-3] to an Attendant Console will not operate...