NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 477
Multiple Call Forwarding - Don’t Answer M-25
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node. 
(Note)
STEP 1:ASYDN - These data must be set to the NCN.
System Data 1...

NEAX2400 IMX Feature Programming Manual
Page 478ND-70184 (E), Issue 3
M-26 Message Center Interface
M-26 Message Center Interface
General Description
This feature provides an interface to an external CPU for Message Center information when a specific UCD [U-1]
group or ATTENDANT CONSOLE [A-3] is called. This interface allows external control of Call Indicator Lamp
(Note) indications on equipped NEAX2400 IMX stations. This feature also provides a socket interface (LAN
interface) for connection to an...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 479
Message Center Interface M-26
Operating Procedure (cont’d)
5. The external CPU, upon receiving retrieved message information, will transmit a data record requesting
the NEAX2400 IMX to extinguish the Call Indicator Lamp of the corresponding station.
Service Conditions
1. The call type is sent to the external CPU via the MCI interface, this call record will pertain to the following
services:
ATTENDANT CAMP-ON [A-1]
AUTOMATIC RECALL...

NEAX2400 IMX Feature Programming Manual
Page 480ND-70184 (E), Issue 3
M-26 Message Center Interface
Service Conditions (cont’d)
4. If the Host/CPU malfunctions and stops collecting call records, the NEAX2400 IMX can store up to 16
call records. If the maximum of 16 call records is stored and a 17th is generated, the system will write over
the oldest stored record, thus giving the stack the most recently generated call records.
5. MCI data will not be output when a hotline station is terminated to a...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 481
Message Center Interface M-26
Interactions
1. In case a Message Center exists on each side of the FCCS network and CCIS network:
a.) Message data will be transmitted to the MC on the side of the CCIS network (in the figure below,
MC#1), provided that a call from any of the FCCS network nodes (in the figure, node A/B/C)
terminates to an ATTCON/UCD station of the non-FCCS node (in the figure, node D).
b.) Message data will be...

NEAX2400 IMX Feature Programming Manual
Page 482ND-70184 (E), Issue 3
M-26 Message Center Interface
Interactions (cont’d)
b.) The shared Message Center also can let the Message Waiting Lamps for both FCCS and non-
FCCS (CCIS) network stations go ON and OFF to inform the telephone user of the message
arrival.
3. In case the Message Center exists only on the side of CCIS network:
a.) Message data will be transmitted to the offered MC (in the figure below, assumed to be connected
to node D), given that a...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 483
Message Center Interface M-26
Interactions (cont’d)
4. In case the Message Center exists only on the side of FCCS network:
a.) Message data will be transmitted to the offered MC (in the figure below, assumed to be connected
to node A), given that a call from the CCIS node (in the figure, node D) terminates to the
ATTCON/UCD station of any of the FCCS network nodes (in the figure, node A, B, C).
b.) The MC, though provided only inside...

NEAX2400 IMX Feature Programming Manual
Page 484ND-70184 (E), Issue 3
M-26 Message Center Interface
Programming (cont’d)
System Data 2, Index 6, Bit 0. Is MCI service with UCD groups to be enabled? 0/1: No/Yes. 
System Data 2, Index 7, Bit 1. Is MCI service for calls via the Attendant Console to be enabled? 0/1:
No/Yes. 
STEP 2:AIOC - Assign the function and attribute data of the IOC ports.
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 485
Message Waiting Lamp Setting - Station M-30
M-30  Message Waiting Lamp Setting - Station
General Description
This feature allows a station to set/cancel a Message Waiting indication or lamp. Any single line telephone or Dterm
can set/cancel Message Waiting indication to any single line telephone equipped with a 90v neon lamp, or a Dterm.
Note:
Call Indicator Lamp on Dterm Series E is used as the Message Waiting Lamp.
Operating...

NEAX2400 IMX Feature Programming Manual
Page 486ND-70184 (E), Issue 3
M-30 Message Waiting Lamp Setting - Station
Operating Procedure (cont’d)
To cancel a Message Waiting Indication from a Dterm or MY Line:
1. Lift the handset or press the SPEAKER key; receive dial tone.
2. Press the Message Waiting Cancel line/feature key, receive special dial tone. 
3. Dial the desired telephone number; the LCD displays, and service set tone is heard.:
4. Message Waiting indication is cancelled.
Service Conditions
1....