NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 807
Call Forwarding - Override - CCIS C-49
C-49 Call Forwarding - Override - CCIS 
General Description
This feature allows a forwarded-to station (Station A) to ring the station (Station B), which has set CALL
FORWARDING - ALL CALLS - CCIS [C-45] to it. If the called station (Station B) has set CALL FORWARDING
- BUSY LINE - CCIS [C-46] to the calling station (Station A), the calling station will receive busy tone and can
activate CALL...

NEAX2400 IMX Feature Programming Manual
Page 808ND-70184 (E), Issue 3
C-50 Call Transfer - All Calls - CCIS
C-50  Call Transfer - All Calls - CCIS
General Description
This service feature allows Inter-Office CALL TRANSFER-ALL CALLS when the transferring station and the
transferred station respectively belong to a different PBX in the CCIS network.
Operating Procedure
1. Station A and C are in connection on a station-to-station call.
2. Station A switch hook flashes; receives special dial tone. Station C...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 809
Call Transfer - All Calls - CCIS C-50
Operating Procedure (cont’d)
3. Station A dials the number for B; receives ringback tone. Station B is rung. (Note 1)
Note 1:
The status of Station A can be restored to normal with a switch hook flash in one of the following cases:
When Station A has received busy tone.
When Station B is under a call restriction or when Station A cannot access Station B for some other reasons.
When Station B does...

NEAX2400 IMX Feature Programming Manual
Page 810ND-70184 (E), Issue 3
C-50 Call Transfer - All Calls - CCIS
Operating Procedure (cont’d)
5. Station A hangs up (Note 3); Stations B and C are connected with each other.
Note 3:
If Station A switch hook flashes instead of hanging up, a three-way connection is set up.
Service Conditions
1. When TRUNK-TO-TRUNK CONNECTION [T-10] is provided, an incoming or outgoing network or TIE
Line call may be transferred to an outgoing network trunk, provided that the trunk...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 811
Call Transfer - All Calls - CCIS C-50
Service Conditions (cont’d)
2. The THREE-WAY CALLING [T-2] feature allows a maximum of three parties on one connection. The
three parties can be:
 Three stations,
 Two stations and one trunk, or 
 One station and two trunks.
3. The maximum number of simultaneous THREE-WAY CALLING [T-2] connections is dependent upon
the quantity of conference trunks (Route 909s) programmed in the system. 
4....

NEAX2400 IMX Feature Programming Manual
Page 812ND-70184 (E), Issue 3
C-50 Call Transfer - All Calls - CCIS
Interactions (cont’d)
4. Upon establishing a CONSULTATION HOLD [C-58] connection and dialing a third party, if the user
receives busy or reorder tone instead of ringback tone, the user flashes once to disconnect the tone and
reconnect the second party.
5. Upon establishing a CONSULTATION HOLD [C-58] connection and dialing a MISCELLANEOUS
TRUNK ACCESS [M-2] code, if no dial tone is given (after the...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 813
Called Station Status Display - CCIS C-51
C-51  Called Station Status Display - CCIS 
General Description
This feature provides for the status of a called station to appear on the LCD display of a calling Dterm using CCIS.
Operating Procedure
Lift the handset or press the SPEAKER key and dial the desired station. The LCD display indicates the status of the
called station.
Service Conditions
1. If the called station is idle, the...

NEAX2400 IMX Feature Programming Manual
Page 814ND-70184 (E), Issue 3
C-52 Calling/Called Number Display - CCIS
C-52 Calling/Called Number Display - CCIS
General Description
This service feature allows an Inter-Office calling/called number display when the Attendant Console and the
calling/called party belong to different offices within the CCIS network. 
If the Attendant dials a telephone number, the dialed telephone number is displayed on the Console (Calling Number
Display). If a station calls an...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 815
Calling/Called Number Display - CCIS C-52
Operating Procedure (cont’d)
2. The Attendant presses the ANSWER key; Station B and the Attendant are connected. The number of
Station B is displayed on the Attendant Console.
Service Conditions
For the Attendant Console:
1. At the time of call origination:
a.) The called number is displayed (last 6 digits) only when the called party has answered the call.
2. At the time of call termination:...

NEAX2400 IMX Feature Programming Manual
Page 816ND-70184 (E), Issue 3
C-53 Call Processing Indication - CCIS
C-53  Call Processing Indication - CCIS 
General Description
This feature provides a visual indication at the ATTENDANT CONSOLE [A-3] of all CCIS calls being handled by
the ATTENDANT CONSOLE [A-3] through the CCIS network.
Operating Procedure
Refer to the operation guide of the Attendant Console.
Service Conditions
1. The status of calls being processed by the Attendant is indicated by the status...