NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 877
Hotline - CCIS H-12
H-12 Hotline - CCIS
General Description
This feature allows two stations at different nodes in the CCIS network to be associated with one another on an
automatic ringdown basis. 
Operating Procedure
1. Station A lifts the handset.
2. Station B is rung.
3. Station B lifts the handset; the connection is established. 
Service Conditions
1. If both phones in a HOTLINE - CCIS pair are equipped with dials, either one may...

NEAX2400 IMX Feature Programming Manual
Page 878ND-70184 (E), Issue 3
H-12 Hotline - CCIS
Programming
STEP 1:ASDT - Assign the station as a TEC = 14 for Hotline.
STEP 2:AHLS - Assign the station number programmed above for the following parameters: 
HOT TN:HOTLINE Tenant
STN: HOTLINE Station
TYP: 2
ADC: Abbreviated Digit Code 
STEP 3:ASPD - Assign tenant, Abbreviated Digit Code (ADC) and Digit Code (DC).  

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 879
Incoming Call Identification - CCIS I-16
I-16 Incoming Call Identification - CCIS
General Description
This feature allows an Attendant to visually identify the type of service and/or trunk route which is arriving or
waiting to be answered at the Attendant Console through CCIS. 
Operating Procedure
No manual operation is required.
Service Conditions
1. A flashing lamp indicates a call waiting to be answered.
2. A steady lamp indicates...

NEAX2400 IMX Feature Programming Manual
Page 880ND-70184 (E), Issue 3
I-16 Incoming Call Identification - CCIS
Programming (cont’d)
Index 8 
Bit 0-Listed Directory Number 
Bit 1-Incoming Station Call 
Bit 2-Attendant Recall
Bit 3-FX
Bit 4-WATS
Bit 5-CCSA (DID)
Bit 6-TIE Line
Bit 7-Call Forwarding Busy Line 
Index 9 
Bit 0-Call Forwarding Don’t Answer
Bit 1-Call Forwarding Intercept 
Bit 2-TF ASAT 
Bit 3-Supervisory Call
Note:
System Data 2, Index 8, Bits 6 & 7, and System Data 2, Index 9, Bit 0-3 can be...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 881
Individual Attendant Access - CCIS I-17
I-17  Individual Attendant Access - CCIS 
General Description
This feature permits a user to call a particular Attendant Console in the CCIS network, via an individual Attendant
Identification Number.
Operating Procedure
1. The user dials an individual Attendant Identification Number. 
2. The directed Attendant receives an INCOMING CALL IDENTIFICATION [I-16] indication and can
answer using the...

NEAX2400 IMX Feature Programming Manual
Page 882ND-70184 (E), Issue 3
I-18 Inter-Position Transfer - CCIS
I-18 Inter-Position Transfer - CCIS
General Description
This feature allows calls to be transferred from one Attendant Console to another through the CCIS network. 
Operating Procedure
To transfer from Console A to Console B:
1. Attendant A presses the START key.
2. Attendant A dials the Attendant Console B Identification Number, or “0” for all Attendant Consoles. 
3. The call is indicated at...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 883
Look Ahead Routing - CCIS L-25
L-25  Look Ahead Routing - CCIS
General Description
This feature allows a station to dial a Public Switched Telephone Network (PSTN) call and has the capability of
looking ahead to seven directly-connected nodes in the CCIS network for an idle trunk.
Operating Procedure
1. Lift the handset; receive dial tone.
2. Dial the access code; receive second dial tone.
3. Dial the PSTN number.
4. The system...

NEAX2400 IMX Feature Programming Manual
Page 884ND-70184 (E), Issue 3
L-25 Look Ahead Routing - CCIS
Programming (cont’d)
If a station in Office A calls a station in Office B, and that station is forwarded to a station in Office A,
the link will become idle between Office A and B after the station in A answers. 
If a station in Office A calls a station in Office B and then transfers the call to Station C (which is also
in Office A), Office B disconnects, and the link which goes to Office A drops. The...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 885
LDN Night Connection - CCIS L-29
L-29 LDN Night Connection - CCIS
General Description
When an LDN incoming call arrives from a CCIS line or other outside line while the System is in Night Mode, this
service feature transfers the call to a transfer destination outside line, including CCIS lines, assigned for that LDN.
Operating Procedure
1. Attendants 1 & 2 in Node A set into Night mode using the NITE key; the Night lamp illuminates...

NEAX2400 IMX Feature Programming Manual
Page 886ND-70184 (E), Issue 3
L-29 LDN Night Connection - CCIS
Operating Procedure (cont’d)
3. Station (B) answers; Stations (B) and (C) are connected with each other. If necessary, the call can be
transferred to another station by means of Call Transfer-All Calls service.
Service Conditions
1. The ranking of this service feature within the Night Connection service is as follows:
 Night Connection Flexible.
 Night Connection Fixed. 
 LDN Night Connection (This...