NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 197
Call Forwarding-Intercept / Announcement C-25
Programming (cont’d)
STEP 6:AAED - Used to assign Announcement equipment. Assign:
TN: Tenant Number
EQP: Announcement Equipment Number
0: Dead Level
1: Unused Number (LCR OPR not programmed)
2: Available
3: Available
4: Outgoing Trunk Group Busy Announcement
5: Available
6: Available
7: Outgoing Route Restriction Announcement
8 ~ 15: Available for ANNOUNCEMENT SERVICE [A-15] applications....

NEAX2400 IMX Feature Programming Manual
Page 198ND-70184 (E), Issue 3
C-25 Call Forwarding-Intercept / Announcement
FCCS Programming (cont’d)
R: Sending RBT
0/1 = Yes/No
A: Answer Signal Sending (Answer from the incoming trunk)
0 = No/Yes Normally assign data “1”.
M: Multiple Connection
0/1 = Single Connection/Multiple Connection
LGRT: Logical Route Number
TK: Trunk Number *Not necessary for “M = 1”
STEP 3:ARRCN - This data must be assigned to the NCN.
Release the restriction between the terminating...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 199
Call Forwarding - Override C-26
C-26 Call Forwarding - Override
General Description
This feature allows a target user (Station A) to call the station (Station B) which has set CALL FORWARDING -
ALL CALLS [C-5] to it. If the called station (Station B) has set the CALL FORWARDING - BUSY LINE [C-2] to
the calling station (Station A), the calling station (Station A) hears busy tone and can activate CALL BACK [C-1],
EXECUTIVE RIGHT-OF-WAY...

NEAX2400 IMX Feature Programming Manual
Page 200ND-70184 (E), Issue 3
C-27D Call Waiting - Answer - Dterm
C-27D Call Waiting - Answer - Dterm
General Description
This service feature allows a Dterm user to answer a CAMPED-ON [A-1] or CALL WAITING [C-12, 31] call while
putting an existing call on HOLD [C-6], by pressing the ANSWER key.
Operating Procedure
CAMP-ON [A-1] or CALL WAITING [C-12, 31] to a busy Dterm is activated: 
1. The user hears Camp-On Indication Tone or Call Waiting Tone during a call in...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 201
Call Waiting - Answer - DtermC-27D
Programming (cont’d)
System Data 2, Index 10, bit 7. Should the warning tone set in System Data 1, Index 152 be
periodically sent? 0/1: No/Yes. Assign on a per tenant basis.
STEP 2:ASFC - Assign a Service Feature Class that allows SFI’s 5, 6, and 11. This allows the ability to
originate a CALL WAITING - ORIGINATE (SFI 5), to terminate a CALL WAITING -
ORIGINATING [C-31] (SFI 6), and to receive...

NEAX2400 IMX Feature Programming Manual
Page 202ND-70184 (E), Issue 3
C-28 Call Forwarding - All Calls - Outside
C-28  Call Forwarding - All Calls - Outside
General Description
This feature allows a call, which originates from a station or trunk and is destined for a station, to be routed to another
station outside the NEAX2400 IMX via the appropriate trunk line. This feature can also be activated from a Dterm
multi-line.
Operating Procedure
To set CALL FORWARDING - ALL CALLS - OUTSIDE: 
1. Lift the...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 203
Call Forwarding - All Calls - Outside C-28
Operating Procedure (cont’d)
To cancel CALL FORWARDING - ALL CALLS - OUTSIDE from a multi-line Dterm: 
1. Lift the handset or press the SPEAKER key; receive dial tone. Press the CALL FORWARDING - ALL
CALLS FORWARD feature key; receive service set tone. The LED of the associated feature key will go
out. The LCD displays:
2. Replace the handset or press the SPEAKER key.
Service Conditions
1....

NEAX2400 IMX Feature Programming Manual
Page 204ND-70184 (E), Issue 3
C-28 Call Forwarding - All Calls - Outside
Service Conditions (cont’d)
13. When the incoming call is forwarding to the public network, be sure to add the outgoing access code +
destination area code or the outgoing access code including destination area code number before dialing
subscriber number.
14. A call can be forwarded to a trunk in the remote node via FCCS link.
Interactions
1. A 24-digit limitation exists in memory for CALL...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 205
Call Forwarding - All Calls - Outside C-28
Programming (cont’d)
System Data 2, Index 6, bit 4. Call-forwarded station restricted from making calls? 0/1: Yes/No.
STEP 2:ANPD - Reserve a number level for feature access and cancel. Assign for Normal (N), Hooking (H),
and Busy (B). Assign NND in accordance with a predetermined numbering plan.
STEP 3:ASPA - Assign an access code to CALL FORWARDING - ALL CALLS [C-5] set SID = 8, and to
CALL...

NEAX2400 IMX Feature Programming Manual
Page 206ND-70184 (E), Issue 3
C-29 Call Park
C-29 Call Park
General Description
This feature enables the Attendant(s) or users to “Park” calls against their own extension numbers. Calls can easily
be retrieved from any station within the system.
Operating Procedure
To park a call from the ATTENDANT CONSOLE [A-3]: 
1. The Attendant presses the CALL PARK key; the CALL PARK number (individual Attendant number) is
automatically selected and displayed at the ATTENDANT...