NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 247
Call Block C-150
Service Conditions (cont’d)
8. This service is activated corresponding to each line. In case a Dterm containing some lines, the Restriction
Number is effective only for the line to be registered the number.
9. When confirming the registered Restriction Number, the number registered on MY LINE is displayed for
5 seconds on the LCD.
10. This service is available only when the predetermined Restriction Number and the...

NEAX2400 IMX Feature Programming Manual
Page 248ND-70184 (E), Issue 3
C-150 Call Block
Service Conditions (cont’d)
12. Feature keys and SIDAs will operate for physical and logical stations, as well as inbound trunk calls with
ANI. It will also light the feature keys for both.
13. The COT card for receiving the Caller ID information is shown below:
14. The LC card for notifying the Caller ID information is shown below.
15. The ELC cards to display the indication for the operation procedure on the LCD when...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 249
Call Block C-150
Programming (cont’d)
TYPE: 1
TN: Tenant number
STN: Station number
CID: Calling number (Maximum 28 digits)
SRV: 5 (Call Block)
Release 5 software or later
STEP 1:ASYD - System Data 1, Index 322, Bit 5. Assign the sending tone when Call Block is set.
0/1 DT/SPDT
SYS1, Index 80, b1. Decide the cancel key for the registered Restriction Number.
0/1 = “#” key, “*” key 
(Note)
Note:
Effective since Release 7 software...

NEAX2400 IMX Feature Programming Manual
Page 250ND-70184 (E), Issue 3
C-151 Call Return
C-151 Call Return
General Description
This feature allows the Dterm or an analog station to save the received calling number and the received number of
the station. The following two types of saving features are available:
 Automatic Saving: The received calling number/number of the station is automatically saved when the sta-
tion rings. The stored number can be dialed by pressing the feature key or dialing the...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 251
Call Return C-151
Operating Procedure (cont’d)
Manual Saving (equal to SAVE AND REPEAT - Dterm [S-24D]
1. Saving Calling Number
a.) Press the S&R key while in conversation using My Line or Sub Line.
b.) The received calling number is saved and the S&R key lights red.
Note:
One calling number can be saved. When a calling number has already saved using SAVE AND REPEAT - Dterm, the
calling number is deleted.
2. Displaying Stored Calling...

NEAX2400 IMX Feature Programming Manual
Page 252ND-70184 (E), Issue 3
C-151 Call Return
Service Conditions (cont’d)
b.) This service is available in the following cases:
 When the trunk incoming call that receives the calling number (Analog COT/ISDN/CCIS trunk)
is directly terminated at the station.
 When the station-to-station call is terminated directly.
c.) When the station answers the call held on Multi Line, the calling number/calling station number
cannot be saved (Held Line is not My Line). When...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 253
Call Return C-151
Service Conditions (cont’d)
e.) The latest calling number is saved in the data memory when the service feature class data (SFI:
155) is “0”. Since the latest calling number remains when SFI:155 is changed from “0” to “1”, the
call origination can be operated with the latest calling number saved before the data is changed.
7. Service Conditions for Manual Saving:
a.) Manual Saving is available for the D
term with the...

NEAX2400 IMX Feature Programming Manual
Page 254ND-70184 (E), Issue 3
C-154 Call Hold Pick Up
C-154 Call Hold Pick Up
General Description
This feature allows a user to pick up a trunk or station call that is put on hold by a second user. The user can
accomplish this by dialing an access code followed by the telephone number that is holding the call.
Operating Procedure
1. Make a trunk or station call to Station A.
2. Station A places the call in progress on hold.
3. From Station B, dial the access code...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 255
Calling Party Number - Name Assignment and Display C-157
C-157                       Calling  P arty Number -  
Name Assignment and Display
General Description
This feature allows a user to assign the desired name for the calling number, which is provided by Central Office,
CCIS or ISDN feature, using the MAT command. The assigned name is displayed on the LCD of the Dterm and the
Desk Console. 
Operating Procedure
No manual operation...

NEAX2400 IMX Feature Programming Manual
Page 256ND-70184 (E), Issue 3
C-157 Calling Party Number - Name Assignment and Display
Service Conditions (cont’d)
12. The Display patterns are shown below:
13. Characters of 8-bit ASCII can be displayed for this feature.
14. When the feature key which assigned FKY = 113 via AKYD is pressed, the display pattern on the LCD
(assigned by the ASYD command) changes according to the following conditions:
 When My Line is Prime Line, Call ID Change Display Key is...