NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 207
Call Park C-29
Service Conditions (cont’d)
CALL WAITING - ORIGINATING [C-31]
CALL WAITING - TERMINATING [C-12]
EXECUTIVE RIGHT-OF-WAY [E-1, E-1D]
10. A station in an ATTENDANT-CONTROLLED CONFERENCE [A-2] cannot be parked.
11. There is no limit to the number of calls that can be parked simultaneously within a system.
12. A parked call will recall to the station that has set the CALL PARK. The recall timer is preprogrammed
into System...

NEAX2400 IMX Feature Programming Manual
Page 208ND-70184 (E), Issue 3
C-29 Call Park
Programming
STEP 1:ASYD - System Data 1, Index 142. For CALL PARK recall, the Miscellaneous Timer Counter is
assigned in bits 0-3. The Timer Class is assigned in bits 4-6. Timer Class of 3=2 seconds. Timer
Counter of 4=30 seconds.
System Data 2, Index 1, bit 0 & 1. CONSULTATION HOLD - ALL CALLS [C-17] allowed or denied.
00: Denied; 01: Originating and Terminating Calls allowed, Tandem Call Denied; 11: All calls
allowed....

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 209
Call Park C-29
FCCS Programming (cont’d)
STEP 3:ASATN - This command must be assigned to designate a specific station number to the Attendant
Console. This number is used to identify the Attendant Console when parking a call.
Note 1:
When using ASYDL or ASYDN to program an FCCS feature, the basic programming of ASYD is required in addition
to ASYDL or ASYDN.
Note 2:
System timers may be set on a network basis in ASYDN. 

NEAX2400 IMX Feature Programming Manual
Page 210ND-70184 (E), Issue 3
C-30 Call Pickup - Direct
C-30  Call Pickup - Direct
General Description
This feature allows a user to pick up a call to any other station in the system by dialing a specific CALL PICKUP-
DIRECT code.
Operating Procedure
To pick up an incoming call:
1. Lift the handset; receive dial tone. 
2. Dial the CALL PICKUP - DIRECT code; receive special dial tone. 
3. Dial the specific telephone number to be picked up; incoming call is connected...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 211
Call Pickup - Direct C-30
Programming (cont’d)
STEP 2:ANPD - Reserve a number level for feature access. Assign for Normal (N), Hooking (H), and Busy
(B).
STEP 3:ASPA - Assign an access code to CALL PICKUP-DIRECT, SRV = SSC (Service Code), SID = 35 for
Connection Status Index (CI) of Normal (N).
STEP 4:ASFC - Assign a Service Feature Class that allows SFI 29 to the stations.
FCCS Programming 
This data setting describes only the...

NEAX2400 IMX Feature Programming Manual
Page 212ND-70184 (E), Issue 3
C-31 Call Waiting - Originating
C-31 Call Waiting - Originating
General Description
This feature provides selected stations with Camp-On capability to a busy internal station.
Operating Procedure
To activate CALL WAITING - ORIGINATING: 
1. Dial the desired telephone number; receive busy tone. 
2. Switch hook flash, receive special dial tone, dial the CALL WAITING - ORIGINATING code; or press
the CW key on the D
term. 
3. Receive Call...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 213
Call Waiting - Originating C-31
Service Conditions (cont’d)
9. When the called station goes on-hook, the Call Waiting ringback tone changes to normal ringback tone to
the calling station.
10. CALL WAITING-ORIGINATING cannot be activated while in CONSULTATION HOLD [C-17] mode.
11. CALL WAITING-ORIGINATING cannot be used in conjunction with DIAL ACCESS TO
ATTENDANT [D-2]. 
12. CALL BACK [C-1] activation is denied if a call is waiting at...

NEAX2400 IMX Feature Programming Manual
Page 214ND-70184 (E), Issue 3
C-31 Call Waiting - Originating
Service Conditions (cont’d)
EXCLUSIVE HOLD - Dterm[E-4D]
EXECUTIVE RIGHT-OF-WAY  [E-1, E-8]
NON-EXCLUSIVE HOLD - D
term[N-7D]
OFF-HOOK QUEUING [O-7]
OUTGOING TRUNK QUEUING [O-2, O-2D]
PRIVACY - D
term [P-14D]
PRIVACY RELEASE [P-18]
THREE-WAY CALLING  [T-2, T-2D]
VOICE CALL - D
term[V-2D]
21. The following service features take precedence over CALL WAITING - ORIGINATING:
CALL FORWARDING - ALL CALLS [C-5]...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 215
Call Waiting - Originating C-31
Programming (cont’d)
STEP 2:ANPD - Reserve a number level for feature access. Assign for Normal (N), Hooking (H), and Busy
(B). Assign NND in accordance with a predetermined numbering plan.
STEP 3:ASPA - Assign an access code to CALL WAITING-ORIGINATING, SRV = SSC (Service Code), SID
= 5 for Connection Status Index (CI) of Busy (B) and Normal (N).
STEP 4:ASFC - Assign to the stations a Service Feature...

NEAX2400 IMX Feature Programming Manual
Page 216ND-70184 (E), Issue 3
C-33 Consecutive Dialing - Attendant
C-33 Consecutive Dialing - Attendant
General Description
This feature gives the ATTENDANT CONSOLE [A-3] the ability to generate DTMF signals while engaged in a
station/trunk connection. These DTMF signals are generated via the dial key pad of the ATTENDANT CONSOLE
[A-3].
Operating Procedure
No manual operation is required.
Service Conditions
1. The ATTENDANT CONSOLE [A-3] can transmit DTMF signals...