NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 237
Call Forwarding - I’m Here C-81
Service Conditions (cont’d)
12. When using the FCCS network, if the destination (target station) is a Dterm, CALL FORWARDING - I’M
HERE can be set or cancelled from a sub line of a Dterm. At that time, the transferred call terminates to the
My Line of the Dterm that sets the service.
13. When using the FCCS network, the service can be set or cancelled when the forwarding station is idle.
14. When using...

NEAX2400 IMX Feature Programming Manual
Page 238ND-70184 (E), Issue 3
C-81 Call Forwarding - I’m Here
FCCS Programming (cont’d)
SYS1, Index5, b1~3. Maximum number of Multiple Call Forwarding - All Calls/Busy Line
occurrences:
Note:
This data is valid when SYS-1, INDEX69, bit 7 is assigned as “1”.
SYS1, Index69, b1. Send short tone when a call forwarded via Call Forwarding - All Calls service is
answered.
0/1 = Not Required/Required
SYS1, Index69, b7. Multiple Call Forwarding - Busy Line/All Calls
0/1 =...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 239
Centrex Compatibility C-109
C-109 Centrex Compatibility
General Description
This feature allows a DTMF type telephone user engaged in a trunk call to send a hooking signal to the called office,
enabling the call to be transferred to another station in that office.
Operating Procedure
Station A is connected to Station B, accommodated in another office.
1. Station A presses switch hook; receives special dial tone of the called office....

NEAX2400 IMX Feature Programming Manual
Page 240ND-70184 (E), Issue 3
C-133 Call Forwarding - Don’t Answer To UCD Queue
C-133 Call Forwarding - Don’t Answer To UCD Queue
General Description
This feature allows calls to a station that has set CALL FORWARDING-DONT ANSWER to a UNIFORM CALL
DISTRIBUTION group to be added to a UCD queue if all stations in the UCD group are busy. (Originally, calls
forwarded to a UCD group would receive reorder tone if all stations in the group were busy.) 
Operating...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 241
Call Hold - Conference C-146
C-146 Call Hold - Conference
General Description
This feature allows a user to establish a conference connection by adding a third party who is held on a multiline of
a Dterm to the existing two-party connection. The held call which is to be added may be a station or trunk call.
Operating Procedure
To operate from a Dterm:
1. Make a trunk/station call using line A on the Dterm.
2. Place the in-progress...

NEAX2400 IMX Feature Programming Manual
Page 242ND-70184 (E), Issue 3
C-146 Call Hold - Conference
Service Conditions (cont’d)
2. This service is available when the call is held by the Dterm HOLD key.
3. When the originally connected party (B) is placed on Exclusive Hold, this service is available only when
the D
term user (A) engages in the call with the third party (C).
4. When the D
term user (A) places the station or trunk (B) on hold, including Exclusive Hold, DUAL HOLD
[D-32D] cannot be activated....

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 243
Call Block C-150
C-150 Call Block
General Description
This feature is a part of Caller ID service. This feature restricts termination of incoming calls from the preassigned
calling numbers. This feature is available by designating the calling number by the MAT.
Call Block is used to restrict an incoming call that has a Restriction Number (Physical Station Number, telephone
number or the Caller ID number, which are preset by each...

NEAX2400 IMX Feature Programming Manual
Page 244ND-70184 (E), Issue 3
C-150 Call Block
Operating Procedure (cont’d)
To set the Restriction Number by dialing an optional number:
1. Lift the handset.
2. Press the CALL BLOCK key.
3. Receive special dial tone.
4. Dial number to be restricted.
5. Receive service set tone after the preassigned inter-digit timer (default is 6 seconds). 
(Note 1)
6. The CALL BLOCK key lights red.
7. The dialed number is registered as the Restriction Number.
When Release 5...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 245
Call Block C-150
Operating Procedure (cont’d)
24 digit display of Dterm Series E
 When the last incoming call is displayed (Release 7 software or later):
 When Restriction Number is set (Release 5 software):
 When confirming the Restriction Number (Release 5 software):
 When confirming the Restriction Number (Release 7 software or later):
 When Restriction Number is cancelled (Release 5 software):
 When HELP Key for CALL BLOCK...

NEAX2400 IMX Feature Programming Manual
Page 246ND-70184 (E), Issue 3
C-150 Call Block
Service Conditions
When the Restriction Number is registered by the MAT:
1. When the calling number is not received, this service is not activated.
2. The calling number for this service is assigned to the parameter CID of ACID command. When only the
first part of the calling number is assigned to the CID, this service is applied to any calling number that
begins with the assigned number. For example, when “0471” is...