NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 227
Call Forwarding - All Calls - Announcement C-69
Programming (cont’d)
STEP 7:ARRC - If a TIE Line, DID or REMOTE ACCESS TO PBX [R-2] connection to the Announcement
Service trunk is required, allow trunk-to-trunk connection using ARI-D-RES, Direct Connection.
STEP 8:AAED - Used to assign announcement equipment.
Assign:
TN: Tenant Number
EQP: Announcement Equipment Number
0: Dead Level
1: Unused Number (LCR OPR not programmed)
2:...

NEAX2400 IMX Feature Programming Manual
Page 228ND-70184 (E), Issue 3
C-73 Call Back - Delayed
C-73 Call Back - Delayed
General Description
This feature allows a station to which CALL BACK [C-1] has been set to initiate another call, within a
predetermined time period after becoming idle and before the CALL BACK [C-1] feature is activated.
Operating Procedure
No manual operation is required.
Service Conditions
1. This feature is assigned in system programming, on a system-wide basis.
2. The CALL...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 229
Call Forwarding - Don’t Answer - Outside C-74
C-74  Call Forwarding - Don’t Answer - Outside
General Description
This feature allows a call which originates from a station or trunk, and is destined for a station, to be routed to another
station outside the NEAX2400 IMX via the appropriate trunk line. This service feature can also be activated from a
D
term multi-line.
Operating Procedure
To set CALL FORWARDING - DONT ANSWER - OUTSIDE:...

NEAX2400 IMX Feature Programming Manual
Page 230ND-70184 (E), Issue 3
C-74 Call Forwarding - Don’t Answer - Outside
Operating Procedure (cont’d)
To cancel CALL FORWARDING - DONT ANSWER - OUTSIDE from a multi-line Dterm: 
1. Press the multi-line key for the station CALL FORWARDING - DONT ANSWER-OUTSIDE is to be
cancelled. 
2. Lift the handset or press the SPEAKER key; receive dial tone.
3. Press the CALL FORWARDING - DONT ANSWER - OUTSIDE feature key; receive service set tone.
The LED of the associated...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 231
Call Forwarding - Don’t Answer - Outside C-74
Service Conditions (cont’d)
b.) When originating a call from a trunk: Restriction for tandem connections between the incoming
trunk and the outgoing trunk selected for the call where CALL FORWARDING - DONT
ANSWER service occurs.
10. There is no limit to the number of stations that may activate this feature simultaneously.
11. When the called station does not answer for a predetermined time...

NEAX2400 IMX Feature Programming Manual
Page 232ND-70184 (E), Issue 3
C-75 Call Forwarding - Intercept / Announcement - Attendant
C-75  Call Forwarding - Intercept / Announcement - 
Attendant
General Description
This feature provides for interception of Attendant-originated calls that cannot be completed (unassigned station,
level, etc.). These calls are automatically routed to a recorded announcement informing the caller that an inoperative
number was reached.
Operating Procedure
No manual operation is...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 233
Call Forwarding - Intercept / Announcement - Attendant C-75
Programming
Programming of hardware into System Data is required. Refer to CALL FORWARDING-
INTERCEPT/ANNOUNCEMENT [C-25]. Timers are also programmed into System Data (see
VARIABLE TIMING PARAMETER [V-1]).
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands...

NEAX2400 IMX Feature Programming Manual
Page 234ND-70184 (E), Issue 3
C-76 Call Waiting Lamp - UCD
C-76  Call Waiting Lamp - UCD
General Description
This feature uses an LED indication, which is one of the programmable keys on the Dterm, to indicate when a call is
waiting to be answered in the UCD queue.
Operating Procedure
No manual operation is required.
Service Conditions
1. The UCD Call Waiting Lamp displays the status of the UCD group as follows:
Lamp On: One or more calls waiting in the UCD queue....

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 235
Call Waiting Lamp - UCD C-76
Interactions (cont’d)
7. If the overflow group is all busy, queuing takes place to the first group and the CALL WAITING LAMP-
UCD will light to indicate a queuing condition at the first group.
8. When a UCD station is assigned as the destination station of LDN Night Connection, this service cannot
be activated.
9. For the FCCS network, this feature is available only for UCD stations in the same node as the...

NEAX2400 IMX Feature Programming Manual
Page 236ND-70184 (E), Issue 3
C-81 Call Forwarding - I’m Here
C-81 Call Forwarding - I’m Here
General Description
This service feature permits the CALL FORWARDING - ALL CALLS feature to be set/cancelled from the target
station.
Operating Procedure
To set CALL FORWARDING - IM HERE from the target station: 
1. Go off-hook; receive dial tone.
2. Dial the CALL FORWARDING - IM HERE access code (from the target station); receive special dial
tone.
3. Dial the forwarding...