NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 267
Digital Display - Station D-5
Service Conditions (cont’d)
c.) answers a Recall or Call Forwarded call.
Example 2: 2-digit TENANT [T-12] number, 4-digit telephone number.
Example 3: 2-digit Trunk Route Restriction Class, 4-digit telephone number.
Example 4: Single digit TENANT [T-12] number, 5-digit telephone number.
Example 5: Single digit Trunk Route Restriction Class, 5-digit telephone number.
Example 6: When 5-digit station...

NEAX2400 IMX Feature Programming Manual
Page 268ND-70184 (E), Issue 3
D-5 Digital Display - Station
Programming (cont’d)
3: TN + 5-digit Station Number
4: RSC + 5-digit Station Number
5: Station Number
FCCS Programming 
No unique programming is required for the FCCS network. 

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 269
Digital Display - Trunk D-6
D-6 Digital Display - Trunk
General Description
This feature provides the Attendant with a visual indication of incoming and outgoing trunk calls on the
ATTENDANT CONSOLE [A-3]. Trunk identification number, trunk route number, and TENANT [T-12] number,
or Central Office trunk code, are displayed in a numerical readout.
Operating Procedure
The DIGITAL DISPLAY TRUNK is automatically activated whenever the...

NEAX2400 IMX Feature Programming Manual
Page 270ND-70184 (E), Issue 3
D-6 Digital Display - Trunk
Service Conditions (cont’d)
e.) an outgoing TIE Line call or re-enters a held trunk call.
7. An Attendant Console also indicates the C.O. code assigned by System Data at each node in the FCCS
network.
Programming
STEP 1:ASYD - System Data 1, Index 68, Bit 1. Type of INDIVIDUAL TRUNK ACCESS, 0/1: Route and
Trunk Number/Central Office Code.
Note:
If System Data 1, Index 68, Bit 1 is assigned for the Individual...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 271
Direct-In Termination (DIT) D-7
D-7 Direct-In Termination (DIT)
General Description
This feature automatically routes incoming public network calls directly to a pre-selected station without Attendant
assistance. The call can then be processed by the called party. THREE-WAY CALLING [T-2], CALL TRANSFER
[C-10], etc., are handled in the same manner as any normal trunk call.
Operating Procedure
The calling party, outside the system,...

NEAX2400 IMX Feature Programming Manual
Page 272ND-70184 (E), Issue 3
D-7 Direct-In Termination (DIT)
Service Conditions (cont’d)
17. When activating this feature via the FCCS network, when the telephone number of the destination station
is deleted:
a.) When the Attendant Console is used, the DIT call terminates to the Attendant Console.
b.) When the Attendant Console is not used, or if the Attendant Console is in night mode, the caller
hears ringback tone.
18. When activating this feature via the FCCS...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 273
Direct-In Termination (DIT) D-7
Programming (cont’d)
STEP 5:ARSC - The DIT target station receiving the call must be assigned a Route Restriction Class (RSC),
allowing the station to be connected to the trunk. The DIT route must be allowed via Route Restriction
Indexes (RRI) 0 & 1.
STEP 6:ACFR - Designate the type of incoming Call Class Indexes (CCI) that require a Transfer Service
Feature Index (TSFI) = 3, DIRECT-IN TERMINATION. The...

NEAX2400 IMX Feature Programming Manual
Page 274ND-70184 (E), Issue 3
D-8 Direct Inward Dialing (DID)
D-8  Direct Inward Dialing (DID)
General Description
This feature provides for all incoming calls from the public network (except FX or WATS) to reach any system
station without Attendant assistance.
Operating Procedure
The calling party, outside the system, dials the telephone number as usual. However, the call is answered directly at
a predetermined station, bypassing the Attendant.
Service Conditions...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 275
Direct Inward Dialing (DID) D-8
Programming
STEP 1:ASYD - System Data 1, Index 16, Bit 3. Enable the 4-digit station number. It is normal to enable all
options regarding length of station numbering. Assign data 1FH.
System Data 1, Index 65. Assign the number of routes in the system.
System Data 1, Index 70, Bit 0. Is Calling Number for a DID incoming to the Attendant in service? 0/
1: No/Yes.
STEP 2:ARTD - Assign the DIRECT INWARD...

NEAX2400 IMX Feature Programming Manual
Page 276ND-70184 (E), Issue 3
D-9 Direct Outward Dialing (DOD)
D-9 Direct Outward Dialing (DOD)
General Description
This feature permits any user to gain access to the public network without the assistance of the Attendant, by dialing
an access code and receiving a second dial tone. The user may then proceed to dial the desired public network
number.
Operating Procedure
To place an outside call:
1. Go off-hook; receive dial tone,
2. Dial the trunk access code...