NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 297
Dial Intercom D-87
Operating Procedure (cont’d)
PRIME LINE PICK UP-Dterm [P-13D]:
The Dterm may be programmed to seize the incoming call on the AUTOMATIC, MANUAL, or DIAL INTERCOM
lines before the Prime Line. If two incoming calls terminate simultaneously to both the Prime Line and the DIAL
INTERCOM line, when the user goes off-hook, PRIME LINE PICKUP-D
term [P-13D] will seize the DIAL
INTERCOM line before the Prime Line. If only the...

NEAX2400 IMX Feature Programming Manual
Page 298ND-70184 (E), Issue 3
D-87 Dial Intercom
Service Conditions (cont’d)
15. DIAL INTERCOM group numbers are either one or two digits and can be set for each DIAL INTERCOM
group:
1 digit: 0-9
2 digits: 00-63
16. The display on the D
term is as follows:
a.) Calling
b.) Called Station AnswersICM                                                      XX
                    (Time Display)  Dial Intercom Number of the Calling Station
* Display appears for 10 seconds...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 299
Dial Intercom D-87
Service Conditions (cont’d)
c.) Intercom Bridge
d.) Intercom Bridge Restriction
17. To answer a call terminated to the INTERCOM line while the Prime Line is busy, press an INTERCOM
line key. 
18. The DIAL INTERCOM ringing by an incoming call is interrupted while the MANUAL SIGNALING [M-
47] signal is being sent out. 
19. While a call is in progress on a multi-line, the AUTOMATIC INTERCOM line, or MANUAL
INTERCOM...

NEAX2400 IMX Feature Programming Manual
Page 300ND-70184 (E), Issue 3
D-87 Dial Intercom
Programming (cont’d)
STEP 2:ADIM - Assign the following data: 
MG: Module Group
G-ID: Group ID Number per MG
N: Number of Digits of Dial Intercom Group (0/1)
0: 1 digit
1: 2 digits 
BCR: Bridge Call Restriction (0/1)
0: Restricted 
1: Allowed
TN: Tenant Number 
ICMCT Number of Intercom Stations (2-64) (actual number to dial)
ICM STN: Intercom Station Number
STEP 3:AKYD - Assign an Intercom Line to the station...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 301
Delayed Ringing - DtermD-90D
D-90D Delayed Ringing - Dterm
General Description
This feature allows a Dterm to receive an incoming ringing signal after a predetermined time.
1. In Boss/Secretary service, a call terminating on the bosss line first rings at the secretarys station. If the
secretary does not answer within a preprogrammed time, the boss station will also ring. This service is
convenient when many lines terminate on a...

NEAX2400 IMX Feature Programming Manual
Page 302ND-70184 (E), Issue 3
D-90D Delayed Ringing - Dterm
General Description (cont’d)
4. This feature may also be used in a similar way to CALL FORWARDING - DONT ANSWER [C-3] or
STATION HUNTING [S-7, 8, 9].
5. A call rings on Station A. If Station A does not answer within a preprogrammed time, the call also rings
on Station B. If the call is not answered within the second preprogrammed time, the call also rings on
Station C. If the call is not answered within...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 303
Delayed Ringing - DtermD-90D
General Description (cont’d)
6. DELAYED RINGING may also be used for calls terminated to single-line telephone appearances on a
Dterm. Calls to single line appearances that are not answered within a preprogrammed time will ring on the
next station in sequence.
7. A call rings on Single Line Station A. If Station A does not answer within a preprogrammed time, the call
also rings on D
term Station B. If the...

NEAX2400 IMX Feature Programming Manual
Page 304ND-70184 (E), Issue 3
D-90D Delayed Ringing - Dterm
Programming
AKYD - Assign the following parameters to stations that will have delayed ringing:
TN: Tenant Number
STN: Station Number
TP: Type of D
term: 0/1
RING: 0: No Ringing 
1: Ringing All Lines
2: Ringing on Prime Line only 
3: Flexible Ring Assignments (Enables RG Parameters)
PL TN STN: Prime Line Tenant and Station Number
KYN: Key Number (1-40)
KYI: Service Index
0: Key Not Used
1: Feature Key
2:...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 305
Delay Announcement - Attendant D-114
D-114 Delay Announcement - Attendant
General Description
This feature provides a recorded announcement to the incoming trunk caller waiting to be answered by the
Attendant. This feature is divided into the following two types, depending on the time when the call is connected
with the announcement trunk.
1. The call is connected to announcement trunk immediately after terminating to the Attendant...

NEAX2400 IMX Feature Programming Manual
Page 306ND-70184 (E), Issue 3
D-114 Delay Announcement - Attendant
Service Conditions (cont’d)
b.) When a call terminates from a trunk where trunk release can be supervised, the trunk will not be
released forcefully, but will be released on its own accord. (Night Transfer station can be
assigned.)
6. This service is not available for incoming calls to an individual Attendant.
7. When a CO line incoming call terminates to a trunk where call clear cannot be confirmed...