NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 337
Emergency Call E-11
Service Conditions (cont’d)
13. When the emergency station is busy, CALL BACK [C-1] to the emergency station is effective (no printout
is performed).
14. When the emergency station is busy, CALL WAITING - ORIGINATING [C-31] and CALL WAITING
- TERMINATING [C-12] are effective, but this service feature is not available. However, when a 2-way
call is made between an emergency station and another station, CALL BACK...

NEAX2400 IMX Feature Programming Manual
Page 338ND-70184 (E), Issue 3
E-18 E911-ANI Unified Number Of Digits
E-18 E911-ANI Unified Number Of Digits
General Description
This service unifies the number of ANI information digits sent out by E911-ANI service. 
Operating Procedure
The operating procedure is the same as for a normal outgoing connection.
Service Conditions
1. The ANI function for E911 outgoing connections is the same as in previous E911-ANI service and is
applicable to the following...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 339
E911-ANI Unified Number Of Digits E-18
Service Conditions (cont’d)
 If ANI data is unassigned:
KP-1
-ST
5. An independent route is required for E911 interface.
6. After the caller’s number is sent to the distant office by E911-ANI, it takes some time until a speech path
is established.
7. Sending data is considered to be not assigned if:
a.) Service version data specifies that Unified Number of Digits is provided,
b.) No data is...

NEAX2400 IMX Feature Programming Manual
Page 340ND-70184 (E), Issue 3
E-18 E911-ANI Unified Number Of Digits
FCCS Programming 
No unique programming is required for the FCCS network. 

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 341
Expanded Multiple Line Operation - DtermE-26
E-26  Expanded Multiple Line Operation - Dterm
          (Series 7400 software feature)
General Description
This feature allows operation of whichever lines from ELC card(s) in the same IMG or in different IMGs in the same
node, as a Dterm’s programmable Multiple Lines (My Line + Prime Line/Sub Lines). While Multiple Line Operation
- Dterm [M-20] only allows such a programming within the...

NEAX2400 IMX Feature Programming Manual
Page 342ND-70184 (E), Issue 3
E-26 Expanded Multiple Line Operation - Dterm
Service Conditions (cont’d)
b.) PA-16ELCJ-B, SW10, Element 1 = OFF: A  Dterm, accommodated on this card, and the other
Lines (other analog telephone/Dterm) can be in
different IMGs (but in the same node). For more
details on the PA-16ELCJ-B circuit card, refer to the
NEAX2400 IMX Circuit Card Manual.
Note:
Even when Element 1 of SW10 is ON, data programming for this feature (Multiple Lines...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 343
Expanded Multiple Line Operation - DtermE-26
Interactions (cont’d)
Serial Call [S-15]
Serial Call - Loop Release [S-64]
Serial Call - CCIS [S-52]
Serial Call - D
term[S-127]
Executive Right-of-Way [E-1, 1D]
Call Back [C-1, 1D]
Message Reminder [M-19, 19D]
Brokerage - Hot Line [B-6]
Split Call Forwarding [S-99]
Call Waiting - Terminating [C-12]
Call Waiting - Answer - D
term[C-27D]
Call Waiting - Originating [C-31]
Note:
Boss-Secretary...

NEAX2400 IMX Feature Programming Manual
Page 344ND-70184 (E), Issue 3
F-1 Flexible Numbering of Stations
F-1 Flexible Numbering of Stations
General Description
This feature provides the ability to assign telephone numbers of the voice station and data station to any
corresponding instrument location, depending solely upon numbering plan limitations.
Operating Procedure
Refer to the NEAX2400 IMX Office Data Specification.
Service Conditions
1. Careful consideration should be given to any numbering...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 345
Flexible Numbering of Stations F-1
Programming (cont’d)
STEP 3:ASPA - Assign the station numbering in such a way that the system will differentiate the station
numbering via the access codes programmed here. The following data is programmed:
The following access codes should also be assigned: 323, 324, 325, 326, 327, 328, 329, 320. CI: N, H;
SRV = STN (Station); and NND: 4 will be assigned with each of the above.
FCCS Programming 
No...

NEAX2400 IMX Feature Programming Manual
Page 346ND-70184 (E), Issue 3
F-2 FX Access
F-2 FX Access
General Description
This feature provides dial access to distant Central Offices using Foreign Exchange (FX) trunks. All incoming calls
to the NEAX2400 IMX from the FX Central Office area are placed to the listed Foreign Exchange Directory number
and are answered by the Attendant in a manner similar to LDN service. Outgoing calls can be made on an Attendant
handled basis using direct or dial access and/or on...