NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 357
Forced Account Code F-7
Programming (cont’d)
System Data 1, Index 13. Each bit in Index 13 directly correlates to a digit in the FORCED
ACCOUNT CODE assigned in AATC, and will determine the second digit of the Check Sum method.
Again pick any bits, 0 to 4, but not the same combination of bits as picked in Index 12.
System Data 1, Index 14. Determines the algorithm used to calculate the last two digits of every
FORCED ACCOUNT CODE....

NEAX2400 IMX Feature Programming Manual
Page 358ND-70184 (E), Issue 3
F-7 Forced Account Code
Programming (cont’d)
STEP 2:ANPD - Reserve a number level for feature access. Assign Connection Index, CI = N, H, B; Normal,
Hooking, and Busy (applicable to any feature assigned to this level). Assign NND in accordance with a
predetermined numbering plan.
STEP 3:ASPA - For SRV = SSC (Service Code) SID = 42, assign the access code. Assign for Connection
Indexes of Normal (N) and Hooking (H).
STEP 4:ASFC - For...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 359
Flexible Assignment of Function Buttons F-17
F-17  Flexible Assignment of Function Buttons
General Description
This feature allows Dterm function (feature) buttons (REDIAL, FEATURE, SPEAKER, CONF, ANSWER,
RECALL, HOLD, and TRANSFER) to be flexibly assigned on each individual Dterm. 
Function (feature) buttons are programmed through the Maintenance Administration Terminal (MAT) and are part
of System Data.
Service Conditions
1. A...

NEAX2400 IMX Feature Programming Manual
Page 360ND-70184 (E), Issue 3
F-31 Follow Phone
F-31 Follow Phone 
General Description
This feature allows individual station data of a terminal to be exchanged with another without the assistance of
MAT. The result of the exchange is printed out in the system message. The exchange of terminal data by this service
is called SWAP service. The following information is included in the system message:
a.) Successful activation: Station data change notice.
b.)...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 361
Follow Phone F-31
Service Conditions (cont’d)
5. Following data assigned to each Dterm will be cleared when this service is activated:
DO NOT DISTURB [D-11] 
LAST NUMBER CALL [L-6]
MESSAGE REMINDER [M-19]
SAVE AND REPEAT [S-24]
6. This service is not available for the following stations: 
a.) Night station (ACSI)
b.) HOT LINE [H-1] station 
c.) HOUSE PHONE [H-2]
d.) Data line, or D
term that has a data line assigned
e.) Station...

NEAX2400 IMX Feature Programming Manual
Page 362ND-70184 (E), Issue 3
F-31 Follow Phone
Service Conditions (cont’d)
12. When this service is activated, the key information of Dterm, which has the target station as a multi-line
will be changed automatically. For example:
13. If the multi-line LED of D
term is lit (busy) when the station swaps, the line LED key may not light
immediately after the service is activated. The LED light normally after the user goes on-hook.
14. For the stations that belong to...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 363
Follow Phone F-31
Service Conditions (cont’d)
21. After this service is activated, and if DM load reset is activated before the data is backed up to the hard
disk, the stations return to the previous status. However, this is not the case with the Speed Calling - One
Touch keys.
22. The DSS Console data does not swap. The My Line of the connected D
term may swap, but in this case,
reassignment of DSS data and cabling will be necessary....

NEAX2400 IMX Feature Programming Manual
Page 364ND-70184 (E), Issue 3
F-35 Flexible Routing - FCCS
F-35  Flexible Routing - FCCS
General Description
With this feature, an FCCS trunk call can automatically be routed via a non-FCCS trunk (C.O. or Tie Line), if all
the FCCS trunks are busy or a Data Link Failure occurs at the FCH card.
Operating Procedure
No manual operation is required.
Service Conditions
1. This feature is activated when all FCCS trunks are busy, a transmission failure occurs, or FCCS...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 365
Flexible Routing - FCCS F-35
Interactions (cont’d)
Note 3:
The display is changed depending on the specification of ACIS.
Note 4:
Has priority over the FLEXIBLE ROUTING - FCCS service. FLEXIBLE ROUTING - FCCS is activated only when
the FCCS trunk for the destination station is busy.
Note 5:
A trunk is used after the call encounters station busy between the stations in the FCCS network.
Note 6:
Available only at the time of the data...

NEAX2400 IMX Feature Programming Manual
Page 366ND-70184 (E), Issue 3
F-36 FCCS Networking via IP
F-36 FCCS Networking via IP
         (Series 7400 software feature)
General Description
This feature allows the system to exchange both speech and FCCS signals over Internet/Intranet. To establish/
release a call, the following two connection patterns can be selected:
 IPTRK Point-to-Point Connection: For both speech and FCCS signal channels, an IPTRK circuit card
is used. At this time, the IPTRK cards in...