NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 397
Intermediate Station Number Display - DtermI-10D
I-10D  Intermediate Station Number Display - Dterm
General Description
This feature provides an LCD display to the called and calling Dterm station when an intermediate station has been
involved in call processing.
Operating Procedure
No manual operation is required.
Service Conditions
1. For a transferred call, the LCD displays:
Note:
When the telephone number of the intermediate or...

NEAX2400 IMX Feature Programming Manual
Page 398ND-70184 (E), Issue 3
I-11 Inter-Office Off-Hook Queuing
I-11  Inter-Office Off-Hook Queuing
General Description
This feature can be employed in a Main-Satellite configuration to allow a Satellite user to queue for LEAST COST
ROUTING - 3/6-DIGIT [L-5] at the Main location. This feature can also be used when all outgoing facilities are
concentrated at the Main location.
Operating Procedure
Operation at the Main location:
1. The Main location receives dialed...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 399
Inter-Office Off-Hook Queuing I-11
Service Conditions (cont’d)
7. OGQ data is transmitted to and stored in the Network Control Node (NCN). Therefore, all the OGQ data
will be cleared by the system initialization of the NCN.
8. When the access to the NCN is impossible (system down or the cable disconnection or trouble has
occurred), the user cannot set or cancel OGQ data. After dialing the access code or pressing the feature
keys for...

NEAX2400 IMX Feature Programming Manual
Page 400ND-70184 (E), Issue 3
I-11 Inter-Office Off-Hook Queuing
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
 (Note 1)
STEP 1:ASYDN - This data must be assigned to the NCN.
System Data 1, Index 41:...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 401
Immediate Ringback Tone I-20
I-20  Immediate Ringback Tone
General Description
IMMEDIATE RINGBACK TONE will be heard by the caller immediately upon determination by the system that
the called station is idle. IMMEDIATE RINGBACK TONE is connected, even if the call occurs during the OFF
portion of the ringing cycle.
Operating Procedure
When a station calls another station or Attendant: 
1. The station goes off hook, hears dial tone, and...

NEAX2400 IMX Feature Programming Manual
Page 402ND-70184 (E), Issue 3
I-21 Internal Zone Paging
I-21 Internal Zone Paging
General Description
This feature allows an individual to make a voice call through the Dterm speakers of the designated group by dialing
the INTERNAL ZONE PAGING access code or pressing the INTERNAL ZONE PAGING key on the Dterm.
Operating Procedure
Voice Call by Internal Zone Paging (Single)
To originate:
1. Lift the handset or press the SPEAKER key; receive dial tone.
2. Dial the...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 403
Internal Zone Paging I-21
Operating Procedure (cont’d)
2. The call is connected to your station.
3. The calling station goes On-Hook.
4. The connection is established between your station and the forwarded party.

(Series 7400 software enhancement) When using the Off-Hook key: (Note)
1. Lift the handset.
2. The call is connected to your station.
3. The calling station goes On-Hook.
4. The connection is established between your...

NEAX2400 IMX Feature Programming Manual
Page 404ND-70184 (E), Issue 3
I-21 Internal Zone Paging
Service Conditions
1. The number of Internal Zone Paging groups is a maximum of 99 groups for each tenant.
2. Each D
term can be a member of multiple Internal Zone Paging groups.
3. A maximum of 255 groups per system can be simultaneously paged using this feature.
4. This feature is activated to idle stations in an Internal Zone Paging group.
5. When all INTERNAL ZONE PAGING groups are busy, busy tone is...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 405
Internal Zone Paging I-21
Programming (cont’d)
IZPSTN: Station number assigned to the INTERNAL ZONE PAGING group
STEP 5:AKYD - For D
term sets, INTERNAL ZONE PAGING can be activated using a programmable line/
feature key. Assign Type:Function:INTERNAL ZONE PAGING [85].
Assign Type:Function:ANSWER [28] for answering INTERNAL ZONE PAGING.
STEP 6:ASFC - Assign a Service Feature Class that allows SFI = 134 to the stations that originate...

NEAX2400 IMX Feature Programming Manual
Page 406ND-70184 (E), Issue 3
L-1 Lamp Check
L-1 Lamp Check
General Description
This feature allows the Attendant, by pressing the LCHK key, to light all lamps and sound the ATTENDANT
CONSOLE [A-3] buzzer.
Operating Procedure
1. Attendant presses the Position Busy key; the LED lights.
2. Attendant simultaneously presses the HOLD, SRC and L3 keys.
3. All lamps will light.
Service Conditions
1. Every lamp field, including the BUSY LAMP FIELD - FLEXIBLE [B-2], will be...