NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 377
Hands-free Dialing/Monitoring - DtermH-5D
H-5D Hands-free Dialing/Monitoring - Dterm
General Description
This feature allows the Dterm user to dial or monitor and call without lifting the handset.
Operating Procedure
To dial a call HANDS-FREE:
1. Press the SPEAKER key; receive dial tone. 
a.) Dial the desired number. 
b.) When the called party answers, lift the handset.
To monitor a call HANDS-FREE: 
1. When placed on hold, press the...

NEAX2400 IMX Feature Programming Manual
Page 378ND-70184 (E), Issue 3
H-9 Hotline - Outside
H-9 Hotline - Outside
General Description
This feature allows a user to access an outside destination by going off-hook or selecting the HOTLINE-OUTSIDE
[H-1] line/feature key and automatically dialing a SPEED CALLING-SYSTEM [S-3] number.
Operating Procedure
To place a HOTLINE - OUTSIDE call using a single-line telephone:
1. User lifts handset.
2. PBX automatically selects a trunk and dials the outside number.
3....

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 379
Hotline - Outside H-9
Programming
STEP 1:ASYD - System Data 2, Index 1, Bit 7. Does TOLL RESTRICTION apply to SPEED CALLING-
SYSTEM [S-3]? 0/1: Yes/No. If TOLL RESTRICTION applies, construct an RSC that will allow the
station access to the outgoing number.
STEP 2:ASFC - Construct a Service Feature Class that allows Service Feature Index (SFI) 12; SPEED
CALLING-SYSTEM [S-3]. Assign this SFC to the Hotline station.
If using a Virtual...

NEAX2400 IMX Feature Programming Manual
Page 380ND-70184 (E), Issue 3
H-9 Hotline - Outside
FCCS Programming (cont’d)
TYPE: 2 (The called party is an outside party)
3 (The called party is a trunk)
CON UGN: User Group Number of the called party (for TYPE=2)
CON ADC: The dialed number for the called party (for TYPE=2)
CON LRN: Logical Route Number of the called party (for TYPE=3)
CON TK: Trunk Number of the called party (for TYPE=3)
Note 1:
When using ASYDL or ASYDN to program an FCCS feature, the basic...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 381
Immediate Ringing I-1
I-1 Immediate Ringing
General Description
This feature causes called stations to ring immediately upon establishment of connections.
Operating Procedure
No manual operation is required.
Service Conditions
1. Ringing is applied to a called station as soon as the switch has determined that the station is idle. There is
no delay caused by waiting for a ring cycle.
2. This feature applies to STATION-TO-STATION...

NEAX2400 IMX Feature Programming Manual
Page 382ND-70184 (E), Issue 3
I-2 Incoming Call Identification
I-2 Incoming Call Identification
General Description
This feature allows an ATTENDANT CONSOLE [A-3] to visually identify the type of service and/or trunk group
that is arriving or waiting to be answered. 
Operating Procedure
No manual operation is required.
Service Conditions
1. A flashing lamp indicates a call waiting to be answered.
2. A steady lamp indicates an answered call.
3. A limit of 12 lamp...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 383
Incoming Call Identification I-2
Programming
STEP 1:ASYD - System Data 2, Indexes 8 & 9, flag the type of incoming calls the Attendant Console should
expect.*
Index 8
 
Bit 0: Listed Directory Number
Bit 1: Incoming Station Call
Bit 2: Attendant Recall 
Bit 3: FX 
Bit 4: WATS 
Bit 5: CCSA (DID) 
Bit 6: TIE Line 
Bit 7: Call Forwarding Busy Line
Index 9 
Bit 0: Call Forwarding Don’t Answer 
Bit 1: Call Forwarding Intercept
Bit 2:...

NEAX2400 IMX Feature Programming Manual
Page 384ND-70184 (E), Issue 3
I-3 Incoming Central Office Call to Tie-Line Connection
I-3  Incoming Central Office Call to Tie-Line 
Connection
General Description
This feature permits an Attendant to connect an incoming public network exchange call, via a TIE Line, to a station
at a distant PBX.
Operating Procedure
To connect an incoming call: 
1. The Attendant presses the LDN key and answers the incoming trunk call. 
2. Dial the TIE Line access code; receive dial...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 385
Incoming Central Office Call to Tie-Line Connection I-3
Interactions (cont’d)
4. Stations must be allowed access to the routes they will need via the appropriate connection status, either
via the Attendant Console (RRI 2) or Direct connection (RRI 3).
5. Various combinations of TRUNK-TO-TRUNK [T-10] connections can be restricted by Alternate Route
Restriction (ARRC command).
Programming
STEP 1:ARTD - Assign the Central Office route as...

NEAX2400 IMX Feature Programming Manual
Page 386ND-70184 (E), Issue 3
I-3 Incoming Central Office Call to Tie-Line Connection
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
STEP 1:ARTDN - Assign the Central Office route as shown below:...