NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 327
Dual Station Call D-156
Interactions (cont’d)
9. This service is not activated when a call is terminated via INTERCOM CALLING [I-9], AUTOMATIC/
MANUAL INTERCOM [A-30], DIAL INTERCOM [D-87] or MANUAL SIGNALING [M-47] (only the
Main Station rings).
10. This service is not activated while CALL BACK [C-1], CALL BACK DELAYED [C-73], CALL BACK-
CCIS [C-44], ATTENDANT CAMP-ON WITH TONE INDICATION [A-1] or ATTENDANT CAMP-
ON WITH TONE...

NEAX2400 IMX Feature Programming Manual
Page 328ND-70184 (E), Issue 3
D-156 Dual Station Call
Programming (cont’d)
LKP (Key Pattern Data):1=16 Line/Feature buttons + 16 DSS keys
2 = 24 Line/Feature buttons + 8 DSS keys
3 = 32 Line/Feature
PG: 0 = Page Change key appears on the soft key (>>>)
1 = Page Change key appears on the feature key
Note 3:
When the soft key data is used on a system basis (SKP=0 is assigned by the ADSL command), this data is not necessary.
FCCS Programming 
Refer to the NEAX2400 IMX...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 329
Executive Right-of-Way E-1
E-1 Executive Right-of-Way
General Description
This feature enables selected users, upon encountering a busy condition at an internal station, to bridge into the busy
connection.
Operating Procedure
To enter a busy connection: 
1. Dial the busy station; receive busy tone.
2. Switch hook flash; receive special dial tone. 
3. Dial the EXECUTIVE RIGHT-OF-WAY access code; warning tone is sent.
4. The calling...

NEAX2400 IMX Feature Programming Manual
Page 330ND-70184 (E), Issue 3
E-1 Executive Right-of-Way
Service Conditions (cont’d)
4. If one party disconnects after the three-way conference bridge is established, the remaining two parties
will still be connected.
5. The EXECUTIVE RIGHT-OF-WAY access code may be assigned according to customer preference.
6. The maximum number of simultaneous Executive Overrides allowable is dependent on the number of
conference function trunks in the system. (Conference...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 331
Executive Right-of-Way - DtermE-1D
E-1D Executive Right-of-Way - Dterm
General Description
This feature enables selected Dterm users, upon encountering a busy condition at an internal station, to bridge into
the busy connection after transmitting a warning tone.
Operating Procedure
To enter a busy connection from a Dterm: 
1. Dial the busy station; receive busy tone. 
2. Press the EXECUTIVE RIGHT-OF-WAY OVER key; the associated LED...

NEAX2400 IMX Feature Programming Manual
Page 332ND-70184 (E), Issue 3
E-1D Executive Right-of-Way - Dterm
Service Conditions (cont’d)
EXCLUSIVE HOLD - Dterm[E-4D] 
NON-EXCLUSIVE HOLD - Dterm[N-7D] 
OFF-HOOK QUEUING  [O-7, O-11] 
OUTGOING TRUNK QUEUING [O-2, O-2D] 
PRIVACY - D
term[P-14D]
PRIVACY RELEASE [P-18] 
THREE-WAY CALLING  [T-2, T-2D] 
VOICE CALL  [V-2, V-7] 
VOICE CALL - D
term[V-2D]
Data Call through Data Adapter / Data Call through Data Module
Note:
In any of the above instances, the calling...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 333
Executive Right-of-Way - DtermE-1D
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node. 
(Note)
STEP 7:ANPDL - Assign first digit of access code for EXECUTIVE RIGHT-OF-WAY....

NEAX2400 IMX Feature Programming Manual
Page 334ND-70184 (E), Issue 3
E-3D Elapsed Time Display - Dterm
E-3D Elapsed Time Display - Dterm
General Description
This feature provides an LCD display of the time elapsed while a Dterm is connected to any trunk.
Operating Procedure
No manual operation is required.
Service Conditions
1. The ELAPSED TIME is displayed in the eight left-side positions of the LCD display.
2. The ELAPSED TIME can reach a maximum of 9 hours, 59 minutes and 59 seconds. After that time,...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 335
Exclusive Hold - DtermE-4D
E-4D Exclusive Hold - Dterm
General Description
This service feature allows a user to place a call on hold and to exclude all other users from retrieving the held call.
Operating Procedure
While a call is in progress: 
1. Press the HOLD key twice; the LCD displays:
                                                                     Held Station or Trunk
2. To return to the held call, press the held line...

NEAX2400 IMX Feature Programming Manual
Page 336ND-70184 (E), Issue 3
E-11 Emergency Call
E-11 Emergency Call
General Description
This feature allows a user to make an EMERGENCY CALL by dialing a special telephone number (emergency
telephone number). Even if the calling station goes on-hook, the calling station is recalled and the speech path is
maintained until the emergency telephone goes on-hook. When a station dials the emergency telephone number, a
system message is printed out to report the...