NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 217
Consecutive Dialing - Attendant C-33
Programming
ASYD - System Data 1, Index 229, Bit 2. DTMF signal sending with the keypad pressed after the
attendant has answered an incoming call 0/1: Out/In Service.
System Data 3, Index 11. Assign a Miscellaneous Timer counter for the duration of the DTMF Sender
Tone. 128ms X (PBST + 1) = Duration of Sender Tone. Maximum value is 2.048 seconds.
765 4 3 2 10
PBST 

NEAX2400 IMX Feature Programming Manual
Page 218ND-70184 (E), Issue 3
C-59 Called Number Display - Attendant
C-59 Called Number Display - Attendant
General Description
If a call is transferred to the ATTENDANT CONSOLE [A-3] as a result of:
DO NOT DISTURB [D-11]
CALL FORWARDING - ALL CALLS [C-5]
CALL FORWARDING - BUSY LINE [C-2]
CALL FORWARDING - DONT ANSWER [C-3]
CALL FORWARDING - INTERCEPT/ ANNOUNCEMENT [C-25]
Information pertaining to the called station is displayed on the Attendant Console.
Operating...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 219
Call Forwarding - Busy Line - Outside C-60
C-60  Call Forwarding - Busy Line - Outside
General Description
This feature allows a call that originates from a station or trunk, and is destined for a station to be routed to another
station outside the NEAX2400 IMX via the appropriate trunk line. This service feature can also be activated from a
D
term multi-line.
Operating Procedure
To set CALL FORWARDING - BUSY LINE - OUTSIDE:
1. Lift...

NEAX2400 IMX Feature Programming Manual
Page 220ND-70184 (E), Issue 3
C-60 Call Forwarding - Busy Line - Outside
Operating Procedure (cont’d)
2. Lift the handset or press the SPEAKER key; receive dial tone.
3. Press the CALL FORWARDING - BUSY LINE - OUTSIDE feature key; receive service set tone. The
LED of the associated feature key will go out. The LCD displays: 
4. Replace the handset or press the SPEAKER key.
Service Conditions
1. CALL FORWARDING - BUSY LINE - OUTSIDE may be set or cancelled by either...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 221
Call Forwarding - Busy Line - Outside C-60
Service Conditions (cont’d)
12. When a caller places a call via OGCA (Outgoing Call Alternative) and when the first outgoing route and
the calling party are restricted, this service cannot be set. In this case, the service can be set via the
following procedure:
a.) assign a dummy route,
b.) clear the restriction between the dummy route and all the stations, and
c.) assign the dummy route as...

NEAX2400 IMX Feature Programming Manual
Page 222ND-70184 (E), Issue 3
C-60 Call Forwarding - Busy Line - Outside
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
 (Note 1)
STEP 1:ANPDL - Reserve a number level for feature access and cancel....

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 223
Consecutive Speed Calling - System C-62
C-62  Consecutive Speed Calling - System
General Description
This feature allows a user to call frequently dialed DID numbers using fewer digits (abbreviated call codes) than
would normally be required. The stored digits would include route access code, area code and office code. The caller
would then manually enter the called telephone number.
Operating Procedure
1. Dial the Speed Calling...

NEAX2400 IMX Feature Programming Manual
Page 224ND-70184 (E), Issue 3
C-62 Consecutive Speed Calling - System
Programming (cont’d)
STEP 3:ASPA - Assign an access code to SPEED CALLING-SYSTEM, assign SRV = SSC (Service Code),
SID = 15. Program for Normal (N). NND = Access code plus Abbreviated Digit Code (ADC). See
ASPD.
Example: 6 + 010
1 digit + 3 digits = NND = 4
STEP 4:ASFC - Assign a Service Feature Class that allows SFI 12 to stations that will have SPEED
CALLING-SYSTEM.
STEP 5:ASPD - Assign the...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 225
Call Forwarding - All Calls - Announcement C-69
C-69  Call Forwarding - All Calls - Announcement
General Description
This feature permits all calls destined for a particular station to be routed to a recorded announcement. Activation
and cancellation may be accomplished by either the individual user or the ATTENDANT CONSOLE [A-3].
Operating Procedure
To activate CALL FORWARDING - ALL CALLS - ANNOUNCEMENT from an individual station:...

NEAX2400 IMX Feature Programming Manual
Page 226ND-70184 (E), Issue 3
C-69 Call Forwarding - All Calls - Announcement
Service Conditions (cont’d)
11. When a designation of CALL FORWARDING - ALL CALLS - ANNOUNCEMENT has already been
assigned, even if the feature is restricted by the new office data or changing of Day/Night mode, the
assigned data can still be used or cancelled.
Programming
Call Forwarding-All Calls
STEP 1:ASYD - System Data 1, Index 4, Bit 6. One burst of ringing at forwarding station...