NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 177
Class Of Service - Individual C-15
C-15  Class Of Service - Individual
General Description
This feature permits all NEAX2400 IMX stations to be assigned a Class of Service in accordance with the degree
of system use desired. Each station is assigned one class from each of three groups.
Operating Procedure
CLASS OF SERVICE - INDIVIDUAL is assigned via system data entry. Thereafter, each station is automatically
provided with the...

NEAX2400 IMX Feature Programming Manual
Page 178ND-70184 (E), Issue 3
C-15 Class Of Service - Individual
Interactions (cont’d)
2. CALL FORWARDING [C-2, 3, 5]: Station-to-station calls can be forwarded to a fully restricted station.
An attempt to forward an incoming trunk call to a fully restricted station will result in reorder tone.
3. STATION HUNTING [S-7, 8, 9]: Any call directed to a busy, fully restricted station will hunt to an
alternate station. Careful consideration is required when assigning a...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 179
Class Of Service - Individual C-15
Programming (cont’d)
TEC: Telephone Class (1-31)
1: DP (10pps)
2: PB
3: DP/PB
12: D
term
13: Data terminal via Dterm
14: Hotline
15: CAS Line
16: Data terminal via Data Module
18: Virtual Circuit
23: ISDN Terminal
27: Eight Conference Equipment
RSC: Route Restriction Class (0-15). For assignment of RSC, ARSC command.
SFC: Service Feature Class (0-15). For assignment of SFC, ASFC command.
STEP 3:ASCL...

NEAX2400 IMX Feature Programming Manual
Page 180ND-70184 (E), Issue 3
C-17 Consultation Hold - All Calls
C-17  Consultation Hold - All Calls
General Description
This feature permits a user to hold any incoming or outgoing public network or TIE Line call, or any intra-office
call, while originating a call to another station within the system.
Operating Procedure
Holding the original call and placing the second call:
1. Press the switch hook; receive special dial tone.
2. The original call is held.
3. Dial...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 181
Consultation Hold - All Calls C-17
Interactions (cont’d)
5. Features that cannot be activated while a user has a party in CONSULTATION HOLD-ALL CALLS are:
EXECUTIVE RIGHT-OF-WAY [E-1]
TRUNK ANSWER FROM ANY STATION [T-8]
CALL BACK, Activate or Cancel [C-1]
CALL PICKUP-DIRECT [C-30]
CALL FORWARDING, Activate or Cancel [C-2, 3, 5]
OUTGOING TRUNK QUEUING, Cancel [O-2]
SPEED CALLING-INDIVIDUAL, Entry [S-21]
MESSAGE REMINDER [M-19D]
6. All...

NEAX2400 IMX Feature Programming Manual
Page 182ND-70184 (E), Issue 3
C-17 Consultation Hold - All Calls
Programming (cont’d)
System Data 1, Index 157. Trunk Soft Hold Timer A, used with senderized trunks. Assign data 00H for
a value of 18 seconds. (Data 31H may be used for a value of two seconds, if CALL TRANSFER-ALL
CALLS [C-11] is to be used immediately after connecting to the trunk.). This is the time between trunk
connection and when switch hook flash is allowed on a senderized trunk connection. It...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 183
Consultation Hold - All Calls - DtermC-17D
C-17D  Consultation Hold - All Calls - Dterm
General Description
This feature permits a Dterm user to hold any incoming or outgoing public network or TIE Line, or any Intra-office
calls, while originating a call to another station within the system.
Operating Procedure
To hold original call and place second call from a Dterm:
1. Press the TRANSFER key; receive special dial tone.
2. The...

NEAX2400 IMX Feature Programming Manual
Page 184ND-70184 (E), Issue 3
C-17D Consultation Hold - All Calls - Dterm
Interactions (cont’d)
5. Features that cannot be activated while a user has a party in CONSULTATION HOLD-ALL CALLS are:
EXECUTIVE RIGHT-OF-WAY [E-1]
TRUNK ANSWER FROM ANY STATION [T-8]
CALL BACK, Activate or Cancel [C-1]
CALL PICKUP-DIRECT [C-30]
CALL FORWARDING, Activate or Cancel [C-2, 3, 5]
OUTGOING TRUNK QUEUING, Cancel [O-2]
SPEED CALLING-INDIVIDUAL, Entry [S-21]
MESSAGE REMINDER...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 185
Consultation Hold - All Calls - DtermC-17D
Programming (cont’d)
System Data 1, Index 157. Trunk Soft Hold Timer A, used with senderized trunks. Assign data 00H for
a value of 18 seconds. (Data 31H may be used for a value of two seconds, if CALL TRANSFER-ALL
CALLS [C-11] is to be used immediately after connecting to the trunk.). This is the time between trunk
connection and when switch hook flash is allowed on a senderized trunk...

NEAX2400 IMX Feature Programming Manual
Page 186ND-70184 (E), Issue 3
C-20 Centralized Attendant Service (CAS)
C-20  Centralized Attendant Service (CAS)
General Description
For applications requiring multiple sites, but having common interests or operation, the NEAX2400 IMX can
operate in a Main (attended) or Satellite (unattended) configuration. Typically, incoming calls to the satellite are
routed to the main location for processing by the Central Attendant(s) within the CAS network. This service...