NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 127
Call Forwarding - Don’t Answer - DtermC-3D
Interactions (cont’d)
6. When CALL FORWARDING-DON’T ANSWER-Dterm is set from Station A to Station B, Station A is
idle, Station B is busy, and Station A will ring. The timer setting in System Data 1, Index 145 is ignored.
7. When a call is call forwarded, the destination station is recorded for STATION MESSAGE DETAIL
RECORDING [S-10].
8. STATION-TO-STATION CALLING [S-11] must first be...

NEAX2400 IMX Feature Programming Manual
Page 128ND-70184 (E), Issue 3
C-3D Call Forwarding - Don’t Answer - Dterm
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node. 
(Note 1)
STEP 1:ASYDL - This data must be assigned to the node set Call...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 129
Call Forwarding - All Calls C-5
C-5 Call Forwarding - All Calls
General Description
This feature permits all calls destined for a particular station to be routed to another station (or to the Attendant)
regardless of the busy or idle status of the called station. Activation and cancellation may be accomplished by either
the individual user or the Attendant.
Operating Procedure
To activate CALL FORWARDING - ALL CALLS from an individual...

NEAX2400 IMX Feature Programming Manual
Page 130ND-70184 (E), Issue 3
C-5 Call Forwarding - All Calls
Service Conditions (cont’d)
8. If the stations own telephone number is set for CALL FORWARDING - ALL CALLS, this feature is
changed to CALLING PARTY RECOGNITION SERVICE (CALL FORWARDING - ALL CALLS)
[C-103].
9. When the user setting CALL FORWARDING - ALL CALLS goes off-hook, special dial tone can be
provided instead of dial tone. (Activation of this service is determined by system data.)
10. The OAI...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 131
Call Forwarding - All Calls C-5
Interactions (cont’d)
7. When CALL FORWARDING-ALL CALLS is in effect, the activating station may be used to originate
calls. See System Data 2, Index 6, Bit 4.
8. When a station is call forwarded, the destination station is recorded for STATION MESSAGE DETAIL
RECORDING [S-10].
9. CALL FORWARDING-ALL CALLS can be overridden, allowing Station B to initiate or transfer calls
back to Station A.
10....

NEAX2400 IMX Feature Programming Manual
Page 132ND-70184 (E), Issue 3
C-5D Call Forwarding - All Calls - Dterm
C-5D  Call Forwarding - All Calls - Dterm
General Description
This feature permits all calls destined for a particular station to be routed to another station, or to the Attendant,
regardless of the busy or idle status of the called station. Activation and cancellation may be accomplished by the
user or the Attendant. CALL FORWARDING - ALL CALLS - D
term may be set or cancelled by the user for...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 133
Call Forwarding - All Calls - DtermC-5D
Operating Procedure (cont’d)
3. Dial the desired target telephone number; receive service set tone. The LED of the associated feature key
does not light at the station setting the service. If the multi-line appearance is another Dterms MY Line,
that stations feature key LED will light. The setting stations LCD displays:
Target Station
4. Replace the handset or press the SPEAKER key.
5. If the...

NEAX2400 IMX Feature Programming Manual
Page 134ND-70184 (E), Issue 3
C-5D Call Forwarding - All Calls - Dterm
Service Conditions (cont’d)
7. A user may set CALL FORWARDING - ALL CALLS - Dterm for a multi-line appearance based on the
CLASS OF SERVICE - INDIVIDUAL [C-15] assigned to the station setting the service. The figure below
is a simplified key sheet assignment for stations 200 & 201. The CLASS OF SERVICE - INDIVIDUAL
[C-15] for station 200 is allowed CALL FORWARDING - ALL CALLS - D
term, but the...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 135
Call Forwarding - All Calls - DtermC-5D
Service Conditions (cont’d)
15. A call can be forwarded to an Attendant Console in the remote node via FCCS link.
16. When a call is forwarded through FCCS link, the numbering plans of the originally called station and the
forwarded Attendant Console must be the same.
Interactions
1. Users are unaccustomed to hearing ringback tone when responding to their own station’s ring. Inform
users when...

NEAX2400 IMX Feature Programming Manual
Page 136ND-70184 (E), Issue 3
C-5D Call Forwarding - All Calls - Dterm
Programming (cont’d)
System Data 1, Index 69, Bit 1 (Bit 2 - Burst of Tone for Recall). A burst of ringback tone to alert the
person receiving a CALL FORWARDING - ALL CALLS - Dterm call. In service? 0/1: No/Yes.
Normally assigned as data “0”.
System Data 2, Index 6, Bit 4. Enables station set for CALL FORWARDING-ALL CALLS-D
term to
be allowed to use phones normally. If data “0” is assigned, the...