NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 107
Call Back - DtermC-1D
Service Conditions (cont’d)
3. CALL BACK to a busy station cannot be established if that station is in the LINE LOCKOUT [L-3] mode.
4. There is no time limit for CALL BACK. Once activated, it will remain in status memory until completed
or manually cancelled.
5. CALL BACK cannot be activated to more than one station at a time. (Calling party).
6. CALL BACK cannot be set by more than one station at a time. (Called...

NEAX2400 IMX Feature Programming Manual
Page 108ND-70184 (E), Issue 3
C-1D Call Back - Dterm
Programming (cont’d)
STEP 6:AT N R - Allow Tenant Restriction Index TRI 0, station-to-station calling for Inter and Intra-tenant
connections.
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 109
Call Forwarding - Busy Line C-2
C-2 Call Forwarding - Busy Line
General Description
This feature permits a call to a busy station to be immediately forwarded to a predesignated station or to the
ATTENDANT CONSOLE [A-3].
If a called station is in a STATION HUNTING [S-7, 8, 9] Group and forwards calls to another Hunt Group, it can
be determined through System Data that the calling party has been directed either to the called parties...

NEAX2400 IMX Feature Programming Manual
Page 110ND-70184 (E), Issue 3
C-2 Call Forwarding - Busy Line
Service Conditions (cont’d)
9. When MULTIPLE CALL FORWARDING - BUSY LINE [M-24] service is activated, hunting will be
performed at the last destination of the forwarded call, even though the multiple jumped stations are in a
Hunt Group.
10. When the pilot station of a STATION HUNTING [S-7, 8, 9] Group activates CALL FORWARDING -
BUSY LINE to a station (not a member of a Hunt Group) and system parameters...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 111
Call Forwarding - Busy Line C-2
Service Conditions (cont’d)
21. This service is available in the following occasions:
a.) When the destination of the CALL FORWARDING - BUSY LINE service is the calling station.
b.) When the calling party is the attendant console or the night station, and the destination of the
CALL FORWARDING - BUSY LINE service is also the attendant console or the night station.
22. SPLIT CALL FORWARDING [S-99] is...

NEAX2400 IMX Feature Programming Manual
Page 112ND-70184 (E), Issue 3
C-2 Call Forwarding - Busy Line
Interactions (cont’d)
9. A calling station, Attendant Console, or trunk can successfully activate EXECUTIVE RIGHT-OF-WAY
[E-1], CALL WAITING-ORIGINATING [C-31], CALL WAITING-TERMINATING [C-12], or BUSY
VERIFICATION [B-3] after having been Call Forwarded and having received busy tone. (A trunk cannot
activate EXECUTIVE RIGHT-OF-WAY [E-1] or BUSY VERIFICATION [B-3]); ASYD - System Data
1, Index 69 = 1, Bit...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 113
Call Forwarding - Busy Line - DtermC-2D
C-2D  Call Forwarding - Busy Line - Dterm
General Description
This feature permits a call to a busy station to immediately be forwarded to a predesignated station, or to the
Attendant. CALL FORWARDING - BUSY LINE - Dterm may be set or cancelled by the user for all multi-line
appearances on the Dterm. Additionally, a single line user may set CALL FORWARDING - BUSY LINE - Dterm for
all sub-lines...

NEAX2400 IMX Feature Programming Manual
Page 114ND-70184 (E), Issue 3
C-2D Call Forwarding - Busy Line - Dterm
Operating Procedure (cont’d)
To set CALL FORWARDING - BUSY LINE - Dterm to a Dterm multi-line:
1. Press the multi-line key for which CALL FORWARDING - BUSY LINE - Dterm feature is to be set.
2. Lift the handset or press the SPEAKER key; receive special dial tone.
3. Press the CALL FORWARDING - BUSY LINE “FORWARD-BY” feature key; receive special dial tone.
4. Dial the desired target telephone...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 115
Call Forwarding - Busy Line - DtermC-2D
Service Conditions (cont’d)
3. This feature is assigned to stations through CLASS OF SERVICE - INDIVIDUAL [C-15] programming
in System Data.
4. There is no limitation to the number of stations that can set CALL FORWARDING - BUSY LINE [C-2]
simultaneously.
5. CALL FORWARDING - BUSY LINE - D
term may also be accessed via the dial pad or SPEED CALLING
- ONE TOUCH [S-22].
Note:
If this feature is...

NEAX2400 IMX Feature Programming Manual
Page 116ND-70184 (E), Issue 3
C-2D Call Forwarding - Busy Line - Dterm
Service Conditions (cont’d)
18. When a station sets CALL FORWARDING - ALL CALLS [C-5] to a pilot in a Hunt Group, and the pilot
activates CALL FORWARDING - BUSY LINE to another station, if the system parameters define the call
to hunt to the forwarded-to Station Hunt Group and all stations are busy, the calling party will hunt at the
called stations Hunt Group. If system parameters assign the...