NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 57
Automatic Number Identification (ANI) A-78
Service Conditions (cont’d)
7. Other interactions are the same as for DTMF signal dialing.
8. FCCS link is not available for this feature.
Programming
STEP 1:ARTD - Assign route class data to the route number of the outgoing trunk.
RT:1
1-OSGS :7 2-ONSG :4 3-ISGS :7 4-INSG :4 15-LSG :5
19-EANI :1
STEP 2:AAND - Assign ANI sending digit as per the route number and the number of digits of the...

NEAX2400 IMX Feature Programming Manual
Page 58ND-70184 (E), Issue 3
A-82 Automated Attendant
A-82 Automated Attendant
General Description
This feature allows a user outside the NEAX2400 IMX to access the system via a public or private network without
the Attendant or users assistance. After or during an announcement, the outside user may originate calls over any
or all of the PBX facilities. 
Operating Procedure
1. The calling party (public or private network) lifts handset; receives dial tone.
2. The...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 59
Automated Attendant A-82
Service Conditions (cont’d)
6. During the first or second announcement, the system can receive DTMF signals. However, when a DTMF
signal is included in the recorded announcement, the announcement stops (first digit reception). Then,
after providing the second announcement, either redial or forced release is selected (inter-digit time-out).
7. After the first or the second announcement, the system does not...

NEAX2400 IMX Feature Programming Manual
Page 60ND-70184 (E), Issue 3
A-82 Automated Attendant
Programming (cont’d)
0/1: Redial is prompted by sending the second announcement/forcible disconnect
Bit 6: Processing on PB Receiver Time-out.
0/1: Forcible disconnection/Transfer to ATT
Index 128: Assign the timer value of Register Prepause Time.
Index 139: Assign the value of No Answer Timer (C.F. - All Calls, Call Back, etc.)
Index 246, Bit 4:
Process of incoming calls (Ringdown) after they encounter their...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 61
Automated Attendant A-82
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node. 
(Note)
STEP 1:ARTDN - Assign the route data of the trunk for AUTOMATED ATTENDANT.
RT:1
1-OSGS :2...

NEAX2400 IMX Feature Programming Manual
Page 62ND-70184 (E), Issue 3
A-98 Answer Hold - Attendant
A-98 Answer Hold - Attendant
General Description
This feature enables an Attendant to answer an incoming call by pressing the ANSWER key or flashing ICI key. If
the Attendant is already engaged in a call, pressing one of these keys places the first call on Hold and automatically
connects the second one. Use of ANSWER key or ICI key speeds call handling, while Answer Hold prevents
accidental call dropping....

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 63
Answer Hold - Attendant A-98
Service Conditions (cont’d)
c.) when the number of available Attendants exceeds the number of incoming calls, the status of
attendant console will be one of the following:
(1) The Attendant will be released from the current call and will be connected to the next incoming
call.
(2) The Attendant will be released from the current call and attendant consoles will be idle.
(3) No change.
4. AUTOMATIC RECALL...

NEAX2400 IMX Feature Programming Manual
Page 64ND-70184 (E), Issue 3
A-99 Authorization Code Display Elimination
A-99  Authorization Code Display Elimination
General Description
This feature eliminates AUTHORIZATION CODE [A-20] and FORCED ACCOUNT CODE [F-7] from being
displayed on the Dterm for security purposes.
Operating Procedure
Procedure 1
(Access code for auth code/forced account code) + (SST) + (auth code/forced account code) + (DT) + (OG
access code) + (OG code)
Dial: (DT) - 10 + (SST) - 1234 +...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 65
Attendant Overflow A-105
A-105 Attendant Overflow
General Description
This feature allows incoming trunk calls directed to the ATTENDANT CONSOLE [A-3] to overflow to a
predetermined station. The trunk call will ring the Attendant for a pre-programmed time period before overflowing
to the destination station.
Operating Procedure
1. An incoming trunk call arrives at the ATTENDANT CONSOLE [A-3].
2. The Attendant is busy or on another call...

NEAX2400 IMX Feature Programming Manual
Page 66ND-70184 (E), Issue 3
A-105 Attendant Overflow
Interactions (cont’d)
3. ATTENDANT OVERFLOW and DELAY ANNOUNCEMENT ATTENDANT [D-114] are mutually
exclusive features.
Programming
STEP 1:ASYD - System Data 1, Index 140. This determines the timer value at which the incoming call will
overflow to the destination station.
System Data 2, Index 15, Bit 1. Set to data “1”. This enables the feature to be assigned via each tenant.
STEP 2:ACSI - Assign CSI = 4, Night...