NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 17
Automatic Recall - DtermA-8D
A-8D Automatic Recall - Dterm
General Description
This feature works as a timed reminder. When a Dterm handled call remains on hold (EXCLUSIVE HOLD [E-4D]
or NON-EXCLUSIVE HOLD [N-7D]) or during an unattended transfer for a variable, programmable period of
time, the D
term is automatically alerted.
Operating Procedure
No manual operation is required.
Service Conditions
1. AUTOMATIC RECALL - Dterm timing is...

NEAX2400 IMX Feature Programming Manual
Page 18ND-70184 (E), Issue 3
A-15 Announcement Service
A-15 Announcement Service
General Description
This feature allows a user to hear a prearranged announcement when the user dials a predetermined access code.
Operating Procedure
1. Lift the handset; receive dial tone. 
2. Dial the announcement trunk access code.
3. Listen to the message from the announcement machine.
Service Conditions
1. This feature requires one of the following hardware alternatives: 
a.)...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 19
Announcement Service A-15
Programming (cont’d)
STEP 3:ARTD - Assign the announcement route as shown below. Be sure to provide privacy by programming
CDN 44:PRV as data “1”.
RT: 1
1-OSGS :2 2-ONSG :3 5-TF :1 6-TCL :1 7-L/T :1
8-RLP :2 15-LSG :4
STEP 4:ARSC - Assign a Route Restriction Class (RSC) to the station that allows access to the Announcement
route. Assign RSC 0 to the Attendant, and allow that RSC access to the Announcement...

NEAX2400 IMX Feature Programming Manual
Page 20ND-70184 (E), Issue 3
A-15 Announcement Service
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
STEP 1:ALRTN - This data must be assigned to the NCN.
Assign the logical route number to the...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 21
Alternate Routing A-16
A-16 Alternate Routing
General Description
This feature automatically routes outgoing on or off-net calls over alternate facilities when the first-choice trunk
group is busy. The user selects the first-choice route by dialing the corresponding access code, and the equipment
then routes the call through alternate trunk groups only if the first is busy. The NEAX2400 IMX will also add or
delete digits, when...

NEAX2400 IMX Feature Programming Manual
Page 22ND-70184 (E), Issue 3
A-16 Alternate Routing
FCCS Programming 
Refer to the NEAX2400 IMX Fusion Network System Manual. 

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 23
Audible Indication Control A-17
A-17 Audible Indication Control
General Description
This feature allows the Attendant to adjust the audible indications provided to the ATTENDANT CONSOLE [A-3].
Operating Procedure
The Attendant Console is equipped with a volume control that can raise or lower the internal speaker level. The
volume control is located on the left side of the Attendant Console. The audible indication may also be turned...

NEAX2400 IMX Feature Programming Manual
Page 24ND-70184 (E), Issue 3
A-18 Account Code
A-18 Account Code
General Description
This feature is an adjunct to STATION MESSAGE DETAIL RECORDING [S-10], which provides a user with the
capability to enter a cost-accounting or client-billing code (up to 10 digits) into the system before dialing a long
distance number.
Operating Procedure
To enter an ACCOUNT CODE: 
1. Lift the handset; receive dial tone.
2. Dial the feature access code; receive service set tone.
3....

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 25
Account Code A-18
Interactions (cont’d)
5. The access code for ACCOUNT CODES is restricted to a maximum of three digits.
6. STATION MESSAGE DETAIL RECORDING [S-10] Split Billing (System Data Option): On transferred
calls, or incoming calls via the Attendant Console, the ACCOUNT CODE will be recorded in all the call
records.
7. When OUTGOING TRUNK QUEUING [O-2] is initiated, the ACCOUNT CODE will be recorded when
the call is completed....

NEAX2400 IMX Feature Programming Manual
Page 26ND-70184 (E), Issue 3
A-18 Account Code
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node. 
(Note)
STEP 1:ANPDL - Reserve a number level for service feature access. Assign Connection Index, CI = N,...