NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 37
Authorization Code - Tie Line Incoming Routes A-29
A-29  Authorization Code - Tie Line Incoming Routes
General Description
This service feature offers an outside party the ability to enter an AUTHORIZATION CODE [A- 20] through an
incoming TIE Line trunk.
Operating Procedure
When the incoming route is restricted or when an AUTHORIZATION CODE [A-20] is always required:
1. The called number, office code, and terminal number are received...

NEAX2400 IMX Feature Programming Manual
Page 38ND-70184 (E), Issue 3
A-29 Authorization Code - Tie Line Incoming Routes
Interactions (cont’d)
6. If ASPA, SRV: LCR (Least Cost Route Selection) / LCRS (Register Sender LCR) AH parameter is
assigned as data “1”, the request for an AUTHORIZATION CODE is determined by the ARSC
assignment of the station in relationship to the route chosen. For AUTHORIZATION CODE - TIE LINE
INCOMING ROUTES, no RSC is assigned against the incoming TIE Line, therefore,...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 39
Authorization Code - Tie Line Incoming Routes A-29
Programming (cont’d)
ASYD - System Data 1, Index 14 determines the algorithm used to calculate the last two digits of
every AUTHORIZATION CODE. (Only decimal numbers may be used in this index, therefore,
hexadecimal values A to F may not be assigned). 
System Data 1, Index 14 = X & Y, where X and Y represent any arbitrarily chosen decimal digit 1- 9,
and where Y is used to determine...

NEAX2400 IMX Feature Programming Manual
Page 40ND-70184 (E), Issue 3
A-29 Authorization Code - Tie Line Incoming Routes
Programming (cont’d)
STEP 3:ASPA - For SRV = SSC (Service Code) SID = 42, assign the access code. For the NND parameter, no
assignment is required when AUTHORIZATION CODE [A-20] operates by itself. When Account
Code [A-18] operates with AUTHORIZATION CODE - TIE LINE INCOMING ROUTES, assign for
SRV = SSC (Service Code), SID = 42. The NND value will include the number of digits in the...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 41
Authorization Code - Tie Line Incoming Routes A-29
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node. 
(Note)
STEP 1:ANPDL - Reserve a number level for feature access. Assign...

NEAX2400 IMX Feature Programming Manual
Page 42ND-70184 (E), Issue 3
A-30 Automatic/Manual Intercom
A-30 Automatic/Manual Intercom
General Description
This feature permits multiple Dterm users to simultaneously call all the stations in a preassigned group, regardless of
their idle/busy status. An INTERCOM member can optionally override another INTERCOM station in a two-party
INTERCOM connection. This service is referred to as INTERCOM BRIDGE. INTERCOM service is separated into
two types, AUTOMATIC...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 43
Automatic/Manual Intercom A-30
Operating Procedure (cont’d)
To bridge into a Manual INTERCOM call: 
1. When two stations are engaged in an INTERCOM call, a third station, belonging to the same INTERCOM
group, will press the MICM key and go off-hook. 
2. A three-party conference is established. The called stations may hear a Warning Tone when the station
bridges into the call. This Warning Tone is preassigned in System Data.
Use of the...

NEAX2400 IMX Feature Programming Manual
Page 44ND-70184 (E), Issue 3
A-30 Automatic/Manual Intercom
Interactions
1. The RECALL key will not operate on an INTERCOM call.
2. THREE-WAY CALLING [T-6] must first be provided.
3. The AICD Command must be assigned before the AKYD command.
4. When assigning the PRI parameter in AKYD, the following data selections are available.
5. No programming is required to enable the SIG key to remain active at all times.
6. The SIG key, when pressed by a calling station,...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 45
Automatic/Manual Intercom A-30
Programming (cont’d)
RING:
0: No Ringing
1: Ringing - All Lines
2: Ringing on Prime Line Only
3: Flexible Ring Assignment, enables RG parameter
PRI: Form of Line Preference (0-3)
KYN: Key Number (1-40)
KYI: Service Index
0: Key not used
1: Feature Key
2: Multi-line Key
KD: Kind of Line
0: Multi-line
1: INTERCOM Line
ICM: Kind of INTERCOM
0: AUTOMATIC INTERCOM
1: MANUAL INTERCOM
2: DIAL INTERCOM
If Manual...

NEAX2400 IMX Feature Programming Manual
Page 46ND-70184 (E), Issue 3
A-52 Account Code - Attendant
A-52 Account Code - Attendant
General Description
This feature provides the ATTENDANT CONSOLE [A-3] with the capability to enter an Account Code into the
system after talking with a CO outgoing/incoming call.
Operating Procedure
The Attendant talks with the CO trunk call.
1. Press the START key.
2. Dial the Account Code feature access code. Service set tone is heard.
3. Dial the Account Code (up to 10...