NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 97
Brokerage Hotline - Outside B-12
Service Conditions (cont’d)
15. The station, the Attendant Console / Desk Console (operator call), and the trunk can be a destination for
Hotline.
16. When Call Forwarding - All Calls/Busy Line/Don’t Answer service has been set to the called station, these
features are available for the call to the station.
17. When a calling party encounters a busy station, the call may bridge into the connection,...

NEAX2400 IMX Feature Programming Manual
Page 98ND-70184 (E), Issue 3
B-12 Brokerage Hotline - Outside
Programming (cont’d)
2: Multi-line Key
KD: 0
RG: Ringing Assignment per multi-line appearance
0: No ringing
1: Ringing in Day mode only
2: Ringing in Night mode only
3: Ringing in Day and Night mode
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 99
Blind Transfer To Attendant B-17
B-17 Blind Transfer To Attendant
General Description
This feature allows a station to transfer a held call (station or trunk) to the Attendant Console and hang up without
having to wait for the Attendant to answer.
Operating Procedure
1. While connected to another party (station or trunk), the user presses switch hook or TRANSFER key;
receives special dial tone.
2. User dials the access code for...

NEAX2400 IMX Feature Programming Manual
Page 100ND-70184 (E), Issue 3
B-17 Blind Transfer To Attendant
Programming
STEP 1:ASYD - System 1, Index 17, Bit 4: (1) Blind Transfer to Attendant In Service.
System Data 2, Index 1, Bit 0 and Bit 1: (1).
STEP 2:ASFC - Cancel the restriction of Blind Transfer to Attendant from SFC of the station. 
(SFI = 103, RES = 1).
STEP 3:ANPD - 0 = Hooking (H) NND = 1.
STEP 4:ASPA - 0 = Hooking (H) SRV = SSC (Service Code), SID = 2.
FCCS Programming 
This data setting...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 101
Blind Transfer To Station B-18
B-18  Blind Transfer To Station
General Description
This feature allows two Class Marks to be assigned to stations, enabling services such as Voice Mail, announcement
machine, etc. depending on the Class Mark.
1. A Class Mark which allows No Answer timer to be extended when the Blind Transferred-to station does
not answer within the predetermined period of time interval.
2. A Class Mark which activates...

NEAX2400 IMX Feature Programming Manual
Page 102ND-70184 (E), Issue 3
B-18 Blind Transfer To Station
Programming (cont’d)
STEP 2:ASFC - Assign the following data to the SFC of the station:
SFI = 103: Assign the timer value of No Answer Timer for BLIND TRANSFER TO STATION.
RES: 0/1 = Index 140 / Timer value assigned by ASYD, SYS-1, INDEX 247
0 = Index 140
1 = Index 247
Also, when ASYD, SYS-1, INDEX 69, b0 = 1 has been assigned, assign the following data to the SFC
of the station:
SFI = 104: Processing in...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 103
Call Back C-1
C-1 Call Back
General Description
This feature provides the ability for a calling station that has dialed a busy station to dial a CALL BACK code. When
this has been done, the calling station will be rung as soon as the busy station becomes available, provided the calling
station is also idle.
Operating Procedure
To set CALL BACK: 
1. Dial the desired telephone number; receive busy tone.
2. Press switch hook for special...

NEAX2400 IMX Feature Programming Manual
Page 104ND-70184 (E), Issue 3
C-1 Call Back
Interactions (cont’d)
3. CALL WAITING - ORIGINATE [C-31] automatic setting and CALL BACK are mutually exclusive.
4. CALL HOLD [C-6]: Activation of CALL BACK is not allowed if the calling or called station has a party
on CALL HOLD [C-6]. CALL BACK can be activated against a D
term that is holding a call or is being
held via EXCLUSIVE HOLD [E-4D] or NON-EXCLUSIVE HOLD [N-7D].
5. Call Back cannot be activated toward the...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 105
Call Back C-1
FCCS Programming (cont’d)
STEP 2:ASPAL - Assign an access code to CALL BACK - Entry, SRV = SSC (Service Code), SID = 3 and a
Connection Status Index (CI) for Busy (B) service. For CALL BACK - Cancel, SRV = SSC (Service
Code), SID = 6. Assign a Connection Status Index (CI) for Normal (N) service.
Note 1:
When using ASYDL or ASYDN to program an FCCS feature, the basic programming of ASYD is required in addition
to ASYDL or...

NEAX2400 IMX Feature Programming Manual
Page 106ND-70184 (E), Issue 3
C-1D Call Back - Dterm
C-1D Call Back - Dterm
General Description
This feature provides the ability for a Dterm, which has dialed a busy station, to press a CALL BACK key. When
this has been done, the calling station will be rung as soon as the busy station becomes available, provided that the
calling station is also free.
Operating Procedure
To set CALL BACK: 
1. Dial desired telephone number; receive busy tone.
2. Press the CALL BACK...