NEC Neax 2400 Imx Feature Programming Manual

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 157
Call Transfer - Attendant C-10
C-10 Call Transfer - Attendant
General Description
This feature permits a user, while connected to an exchange network call, to signal the Attendant and have the
Attendant transfer the call to another station within the system.
Operating Procedure
Calling the Attendant: 
1. While engaged in a Central Office trunk call, press the switch hook; receive special dial tone.
2. Dial the operator access code....

NEAX2400 IMX Feature Programming Manual
Page 158ND-70184 (E), Issue 3
C-10 Call Transfer - Attendant
Interactions (cont’d)
7. A CALL TRANSFER to a station with CALL FORWARDING [C-2, 3, 5] set will forward according to
the conditions of the feature set, unless the station is set to CALL FORWARD - ALL CALLS [C-5] to the
Attendant Console. CALL FORWARDING-OVERRIDE [C-26] supersedes CALL FORWARDING-
ALL CALLS [C-5].
8. A CALL TRANSFER to a station in a STATION HUNTING [S-7, 8, 9] group will hunt according to...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 159
Call Transfer - All Calls C-11
C-11  Call Transfer - All Calls
General Description
This feature permits a user to transfer incoming or outgoing Central Office and intra-office calls to another station
within the system without Attendant assistance.
(Series 7400 software enhancement) The user can set Camp-on function to the busy destination while transferring
an incoming call (Camp-on by Station). With this feature, the trunk party is...

NEAX2400 IMX Feature Programming Manual
Page 160ND-70184 (E), Issue 3
C-11 Call Transfer - All Calls
Service Conditions
1. The station performing the CALL TRANSFER - ALL CALLS can drop off the connection before the
called party answers. If the called station does not answer within the predetermined time, ringing signal is
returned to the transferring station. See VARIABLE TIMING PARAMETERS [V-1] for other selectable
timing choices.
2. In the case of outgoing calls (no answer supervision), this feature...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 161
Call Transfer - All Calls C-11
Service Conditions (cont’d)
14.(Series 7400 software enhancement) The Camp-on by Station is restricted when the target station is in
the three-party connection.
15.
(Series 7400 software enhancement) The Camp-on by Station is not available for the target station in
LINE LOCKOUT [L-3] condition.
16.
(Series 7400 software enhancement) The Camp-on by Station is not available in the following cases:
a.) When...

NEAX2400 IMX Feature Programming Manual
Page 162ND-70184 (E), Issue 3
C-11 Call Transfer - All Calls
Interactions
1. This feature is denied whenever the transferring station is engaged in any state other than a simple two-
party connection.
2. See TRUNK-TO-TRUNK CONNECTION [T-10] for additional programming if the call is to be
transferred off network.
3. If a station is in an established THREE-WAY CALLING [T-2] connection, that station cannot activate
any features. If a station switch hook flashes to...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 163
Call Transfer - All Calls C-11
Interactions (cont’d)
13.(Series 7400 software enhancement) The Camp-on by Station is not available when the target station
uses PRIVACY RELEASE [P-18]. 
(Note)
Note:
The operating station hears busy tone when the destination is in the above condition.
14.(Series 7400 software enhancement) When the Camp-on by Station is set by automatic operation and
the destination station is the UCD group member, BLIND...

NEAX2400 IMX Feature Programming Manual
Page 164ND-70184 (E), Issue 3
C-11D Call Transfer - All Calls - Dterm
C-11D  Call Transfer - All Calls - Dterm
General Description
This feature permits a Dterm user to transfer incoming or outgoing calls without Attendant assistance.
(Series 7400 software enhancement) The Dterm user can set Camp-on function to the busy destination while
transferring an incoming call (Camp-on by Station). With this feature, the trunk party is called back directly as the
destination...

NEAX2400 IMX Feature Programming Manual
ND-70184 (E), Issue 3
Page 165
Call Transfer - All Calls - DtermC-11D
Operating Procedure (cont’d)
3. Method of operation:
a.) When the access code is used, press the FLASH key; receive special dial tone and no indication
on the LCD display, then dial the access code of CALL BACK; receive service set tone.
b.) When the feature key/soft key is used, press the CALL BACK key; receive service set tone. The
LCD of the operating station displays as mentioned above in the...

NEAX2400 IMX Feature Programming Manual
Page 166ND-70184 (E), Issue 3
C-11D Call Transfer - All Calls - Dterm
Operating Procedure (cont’d)
2. Dial the third party, and the third party is busy; receive busy tone. The LCD of the operating station
displays:
                                   The extension number of the third party
3. Replace the handset. The station to be set Camp-on by Station hears Warning Tone. The LCD of the
operating party displays:
The LCD display is changed after the trunk receives...