NEC Neax 2400 Imx Business Features And Specifications

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 281
Hands-free Dialing/Monitoring - DtermH-5D
H-5D Hands-free Dialing/Monitoring - Dterm
General Description
This feature allows the Dterm user to dial or monitor and call without lifting the handset.
Operating Procedure
To dial a call HANDS-FREE:
1. Press the SPEAKER key; receive dial tone. 
a.) Dial the desired number. 
b.) When the called party answers, lift the handset.
To monitor a call HANDS-FREE: 
1. When placed on hold,...

NEAX2400 IMX Business Features and Specifications
Page 282NDA-24221, Issue 3
H-9 Hotline - Outside
H-9 Hotline - Outside
General Description
This feature allows a user to access an outside destination by going off-hook or selecting the HOTLINE-OUTSIDE
[H-1] line/feature key and automatically dialing a SPEED CALLING-SYSTEM [S-3] number.
Operating Procedure
To place a HOTLINE - OUTSIDE call using a single-line telephone:
1. User lifts handset.
2. PBX automatically selects a trunk and dials the outside...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 283
Immediate Ringing I-1
I-1 Immediate Ringing
General Description
This feature causes called stations to ring immediately upon establishment of connections.
Operating Procedure
No manual operation is required.
Service Conditions
1. Ringing is applied to a called station as soon as the switch has determined that the station is idle. There is
no delay caused by waiting for a ring cycle.
2. This feature applies to STATION-TO-STATION...

NEAX2400 IMX Business Features and Specifications
Page 284NDA-24221, Issue 3
I-2 Incoming Call Identification
I-2 Incoming Call Identification
General Description
This feature allows an ATTENDANT CONSOLE [A-3] to visually identify the type of service and/or trunk group
that is arriving or waiting to be answered. 
Operating Procedure
No manual operation is required.
Service Conditions
1. A flashing lamp indicates a call waiting to be answered.
2. A steady lamp indicates an answered call.
3. A limit of 12...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 285
Incoming Central Office Call to Tie-Line Connection I-3
I-3  Incoming Central Office Call to Tie-Line 
Connection
General Description
This feature permits an Attendant to connect an incoming public network exchange call, via a TIE Line, to a station
at a distant PBX.
Operating Procedure
To connect an incoming call: 
1. The Attendant presses the LDN key and answers the incoming trunk call. 
2. Dial the TIE Line access code;...

NEAX2400 IMX Business Features and Specifications
Page 286NDA-24221, Issue 3
I-3 Incoming Central Office Call to Tie-Line Connection
Interactions (cont’d)
4. Stations must be allowed access to the routes they will need via the appropriate connection status, either
via the Attendant Console (RRI 2) or Direct connection (RRI 3).
5. Various combinations of TRUNK-TO-TRUNK [T-10] connections can be restricted by Alternate Route
Restriction (ARRC command). 

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 287
Individual Trunk Access I-4
I-4 Individual Trunk Access
General Description
This feature permits an Attendant to access an individual trunk within a trunk group via dial access at the
ATTENDANT CONSOLE [A-3].
Operating Procedure
1. Press the TKSL key. 
2. Dial the trunk route number (2 digits or 3 digits).
3. Dial the trunk identification number (3 digits).
4. If the trunk is idle, dial tone will be received.
OR
1. Press an...

NEAX2400 IMX Business Features and Specifications
Page 288NDA-24221, Issue 3
I-5 Inter-position Transfer
I-5 Inter-position Transfer
General Description
This feature allows Attendants to transfer calls at their ATTENDANT CONSOLE [A-3] to another Attendants
Console in systems where MULTIPLE CONSOLE OPERATION [M-4] has been provided.
Operating Procedure
To transfer a call from Attendant Console A to Attendant Console B:
1. Press the START key.
2. Attendant A dials Attendant Console B identification number,...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 289
Individual Attendant Access I-6
I-6 Individual Attendant Access
General Description
This feature permits a user to call a particular ATTENDANT CONSOLE [A-3] via an individual Attendant
identification number.
Operating Procedure
1. The user dials the individual Attendant identification number.
2. The directed Attendant gets INCOMING CALL IDENTIFICATION (ICI) [I-2] indication (“ATND”) and
can answer using the normal operating...

NEAX2400 IMX Business Features and Specifications
Page 290NDA-24221, Issue 3
I-7D I-Hold Indication - Dterm
I-7D  I-Hold Indication - Dterm
General Description
This feature provides the Dterm with a distinctive flash to differentiate between a call the user placed on hold from
other calls.
Operating Procedure
No manual operation is required.
Service Conditions
Condition of the LED is as follows:
Burst Wink
LIT On
Off0 0.5 1.0 1.5 Seconds