NEC Neax 2400 Imx Business Features And Specifications

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 291
I-Use Indication - DtermI-8D
I-8D I-Use Indication - Dterm
General Description
This feature provides the Dterm with a unique LED indication to display the particular line the user is on.
Operating Procedure
Manual operation is not required.
Service Conditions
Condition of LED is as follows:
    Burst Wink
On
Off0.5 1.01.5Seconds
Lit 

NEAX2400 IMX Business Features and Specifications
Page 292NDA-24221, Issue 3
I-9 Intercom Calling
I-9 Intercom Calling
General Description
This feature allows a sub-line appearance, assigned to a Dterm, to be used for INTERCOM CALLING.
Operating Procedure
To originate an intercom call:
1. Press the Intercom sub-line appearance. 
2. Lift the handset or press the SPEAKER key; dial tone is heard. 
3. Dial an Intercom station, receive ringback tone. The display will show:
4. The called party answers and the...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 293
Intercom Calling I-9
Interactions (cont’d)
3. All My-line STATION-TO-STATION CALLING [S-11] capabilities such as VOICE CALL-Dterm [V-
2D], MESSAGE REMINDER-Dterm [M-19D], CALL BACK [C-1], etc. are denied because INTERCOM
CALLING uses a virtual circuit sub-line appearance. 
4. An incoming Intercom Call will be provided with distinctive three-burst ringing.
5. An intercom station is only allowed to call other intercom stations....

NEAX2400 IMX Business Features and Specifications
Page 294NDA-24221, Issue 3
I-10D Intermediate Station Number Display - Dterm
I-10D  Intermediate Station Number Display - Dterm
General Description
This feature provides an LCD display to the called and calling Dterm station when an intermediate station has been
involved in call processing.
Operating Procedure
No manual operation is required.
Service Conditions
1. For a transferred call, the LCD displays:
Note:When the telephone number of the intermediate...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 295
Inter-Office Off-Hook Queuing I-11
I-11  Inter-Office Off-Hook Queuing
General Description
This feature can be employed in a Main-Satellite configuration to allow a Satellite user to queue for LEAST COST
ROUTING - 3/6-DIGIT [L-5] at the Main location. This feature can also be used when all outgoing facilities are
concentrated at the Main location.
Operating Procedure
Operation at the Main location:
1. The Main location receives...

NEAX2400 IMX Business Features and Specifications
Page 296NDA-24221, Issue 3
I-11 Inter-Office Off-Hook Queuing
Service Conditions (cont’d)
7. OGQ data is transmitted to and stored in the Network Control Node (NCN). Therefore, all the OGQ data
will be cleared by the system initialization of the NCN.
8. When the access to the NCN is impossible (system down or the cable disconnection or trouble has
occurred), the user cannot set or cancel OGQ data. After dialing the access code or pressing the feature
keys...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 297
Immediate Ringback Tone I-20
I-20  Immediate Ringback Tone
General Description
IMMEDIATE RINGBACK TONE will be heard by the caller immediately upon determination by the system that
the called station is idle. IMMEDIATE RINGBACK TONE is connected, even if the call occurs during the OFF
portion of the ringing cycle.
Operating Procedure
When a station calls another station or Attendant: 
1. The station goes off hook, hears dial...

NEAX2400 IMX Business Features and Specifications
Page 298NDA-24221, Issue 3
I-21 Internal Zone Paging
I-21 Internal Zone Paging
General Description
This feature allows an individual to make a voice call through the Dterm speakers of the designated group by dialing
the INTERNAL ZONE PAGING access code or pressing the INTERNAL ZONE PAGING key on the Dterm.
Operating Procedure
Voice Call by Internal Zone Paging (Single)
To originate:
1. Lift the handset or press the SPEAKER key; receive dial tone.
2. Dial...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 299
Internal Zone Paging I-21
Operating Procedure (cont’d)
2. The call is connected to your station.
3. The calling station goes On-Hook.
4. The connection is established between your station and the forwarded party.

(Series 7400 software enhancement) When using the Off-Hook key: (Note)
1. Lift the handset.
2. The call is connected to your station.
3. The calling station goes On-Hook.
4. The connection is established between your...

NEAX2400 IMX Business Features and Specifications
Page 300NDA-24221, Issue 3
I-21 Internal Zone Paging
Service Conditions
1. The number of Internal Zone Paging groups is a maximum of 99 groups for each tenant.
2. Each D
term can be a member of multiple Internal Zone Paging groups.
3. A maximum of 255 groups per system can be simultaneously paged using this feature.
4. This feature is activated to idle stations in an Internal Zone Paging group.
5. When all INTERNAL ZONE PAGING groups are busy, busy tone...