NEC Neax 2400 Imx Business Features And Specifications

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 311
Last Number Called - DtermL-6D
Service Conditions (cont’d)
Stack #1
Stack #2
Stack #3
Stack #4
Stack #5
Yes
No
The dialed destination and the number stored in the Stack Memory 5 are the same?
The dialed destination and the number stored in the Stack Memory 4 are the same?
NoDialed No.  
Stored
Stack #1
Stack #2
Stack #3
Stack #4
Stack #5
Yes
The system stores the newly dialed destination, removing the oldest number
X Removed...

NEAX2400 IMX Business Features and Specifications
Page 312NDA-24221, Issue 3
L-7D Line Reconnect - Same Line - Dterm
L-7D Line Reconnect - Same Line - Dterm
General Description
This feature allows a user to disconnect a call and receive dial tone by pressing the RECALL key.
Operating Procedure
While a call is in progress: 
1. Press the RECALL key; disconnect and receive dial tone on the same line. 
2. User is ready to dial again.
Service Conditions
1. Conflicting service features are: CALL TRANSFER - ALL...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 313
Line Reconnect - Other Line - DtermL-8D
L-8D  Line Reconnect - Other Line - Dterm
General Description
This feature allows a user to select another line key without going on-hook.
Operating Procedure
While off-hook on the original line, press a line key that is either idle or ringing; the user is disconnected from the
original line and connected to the new line.
Service Conditions
1. LINE RECONNECT - OTHER LINE Dterm cannot be...

NEAX2400 IMX Business Features and Specifications
Page 314NDA-24221, Issue 3
L-9D Line Pre-selection - Dterm
L-9D Line Pre-selection - Dterm
General Description
This feature provides the user with the ability to select an idle or ringing line before going off-hook.
Operating Procedure
To originate:
1. Press the desired line key; receive dial tone. 
2. Dial the desired destination.
To answer:
1. Press the line key (ringing and flashing LED alerts incoming call). 
2. Lift the handset or press SPEAKER key;...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 315
LCR - Time Of Day Routing L-10
L-10  LCR - Time Of Day Routing
General Description
This feature provides automatic routing of outgoing calls over alternative customer facilities, based on the
destination code. The system will select the most economical route available at the time of connection. The pattern
of alternate routing can be changed up to 8 times per day, based on a prearranged time schedule.
Operating Procedure
1....

NEAX2400 IMX Business Features and Specifications
Page 316NDA-24221, Issue 3
L-11 Line Load Control
L-11 Line Load Control
General Description
This feature allows the Attendant to deny a preselected group of stations the ability to originate calls by activating
a key. The sole intention of this feature is to temporarily restrict the least important internal stations from outward
calling during an excessive traffic load or emergency conditions.
Operating Procedure
To activate LINE LOAD CONTROL from the...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 317
Line Load Control - Automatic L-20
L-20  Line Load Control - Automatic
General Description
This feature allows the system to automatically deny a preselected group of stations the ability to originate calls. The
sole intention of this feature is to temporarily restrict the least important internal stations from outward calling
during an excessive traffic load or emergency conditions.
Operating Procedure
No manual operation is...

NEAX2400 IMX Business Features and Specifications
Page 318NDA-24221, Issue 3
L-21 Line Load Control - MAT
L-21 Line Load Control - MAT
General Description
This feature allows the MAT [M-18] to deny a preselected group of stations the ability to originate calls by activating
a command key. The sole intention of this feature is to temporarily restrict the least important internal stations from
outward calling during an excessive traffic load or emergency conditions.
Operating Procedure
The ALLC command is...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 319
Listed Directory Number L-24
L-24 Listed Directory Number
General Description
This feature allows Listed Directory Number Display on the ATTENDANT CONSOLE [A-3] when the Attendant
has answered a Listed Directory Number call.
Operating Procedure
1. The Attendant at an ATTENDANT CONSOLE [A-3] answers an incoming call (DID, TIE).
a.) The DEST lamp lights up.
b.) The Listed Directory Number is displayed.
2. The Attendant presses...

NEAX2400 IMX Business Features and Specifications
Page 320NDA-24221, Issue 3
L-28 LDN Night Connection
L-28 LDN Night Connection
General Description
This service feature routes LISTED DIRECTORY NUMBER (LDN) calls to a preselected station when the system
is in night mode.
Operating Procedure
To answer LDN NIGHT CONNECTION calls (DID, TIE):
1. An incoming LDN call in night mode is automatically routed to a preselected LDN NIGHT
CONNECTION station within the system. 
2. The calling party receives ringback...