NEC Neax 2400 Imx Business Features And Specifications

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 261
Faulty Trunk Report F-6
F-6 Faulty Trunk Report
General Description
This feature allows a station to report a noisy or faulty trunk number by dialing a special access code before hanging
up. The FAULTY TRUNK REPORT consists of a trunk number, telephone number, associated time division switch
and reported time. This information is displayed at the MAINTENANCE ADMINISTRATION TERMINAL
(MAT) [M-18] and/or system printer.
Operating...

NEAX2400 IMX Business Features and Specifications
Page 262NDA-24221, Issue 3
F-7 Forced Account Code
F-7 Forced Account Code
General Description
This feature is a variation of the ACCOUNT CODE [A-18] feature, which makes it mandatory to enter an
ACCOUNT CODE (up to 10 digits) for all outgoing calls. The account code must be dialed before dialing the
outgoing number. Calls are processed only when the dialed account code is valid.
The FORCED ACCOUNT CODE can be masked on the D
term display if necessary...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 263
Forced Account Code F-7
Service Conditions (cont’d)
Note:There are two methods of FORCED ACCOUNT CODE assignment. These methods are Full Implementation and the
Check Sum method. In the Full Implementation method, the whole FORCED ACCOUNT CODE is assigned in the
AATC command and System Data 1, Indexes 12, 13, & 14 are assigned 00H. In the Check Sum method, partial
assignment for each FORCED ACCOUNT CODE is assigned in the AATC...

NEAX2400 IMX Business Features and Specifications
Page 264NDA-24221, Issue 3
F-17 Flexible Assignment of Function Buttons
F-17  Flexible Assignment of Function Buttons
General Description
This feature allows Dterm function (feature) buttons (REDIAL, FEATURE, SPEAKER, CONF, ANSWER,
RECALL, HOLD, and TRANSFER) to be flexibly assigned on each individual Dterm. 
Function (feature) buttons are programmed through the Maintenance Administration Terminal (MAT) and are part
of System Data.
Service Conditions
1. A...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 265
Follow Phone F-31
F-31 Follow Phone 
General Description
This feature allows individual station data of a terminal to be exchanged with another without the assistance of
MAT. The result of the exchange is printed out in the system message. The exchange of terminal data by this service
is called SWAP service. The following information is included in the system message:
a.) Successful activation: Station data change notice.
b.)...

NEAX2400 IMX Business Features and Specifications
Page 266NDA-24221, Issue 3
F-31 Follow Phone
Service Conditions (cont’d)
5. Following data assigned to each Dterm will be cleared when this service is activated:
DO NOT DISTURB [D-11] 
LAST NUMBER CALL [L-6]
MESSAGE REMINDER [M-19]
SAVE AND REPEAT [S-24]
6. This service is not available for the following stations: 
a.) Night station (ACSI)
b.) HOT LINE [H-1] station 
c.) HOUSE PHONE [H-2]
d.) Data line, or D
term that has a data line assigned
e.) Station...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 267
Follow Phone F-31
Service Conditions (cont’d)
12. When this service is activated, the key information of Dterm, which has the target station as a multi-line
will be changed automatically. For example:
13. If the multi-line LED of D
term is lit (busy) when the station swaps, the line LED key may not light
immediately after the service is activated. The LED light normally after the user goes on-hook.
14. For the stations that...

NEAX2400 IMX Business Features and Specifications
Page 268NDA-24221, Issue 3
F-31 Follow Phone
Service Conditions (cont’d)
21. After this service is activated, and if DM load reset is activated before the data is backed up to the hard
disk, the stations return to the previous status. However, this is not the case with the Speed Calling - One
Touch keys.
22. The DSS Console data does not swap. The My Line of the connected D
term may swap, but in this case,
reassignment of DSS data and cabling will be...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 269
Flexible Routing - FCCS F-35
F-35  Flexible Routing - FCCS
General Description
With this feature, an FCCS trunk call can automatically be routed via a non-FCCS trunk (C.O. or Tie Line), if all
the FCCS trunks are busy or a Data Link Failure occurs at the FCH card.
Operating Procedure
No manual operation is required.
Service Conditions
1. This feature is activated when all FCCS trunks are busy, a transmission failure occurs, or...

NEAX2400 IMX Business Features and Specifications
Page 270NDA-24221, Issue 3
F-35 Flexible Routing - FCCS
Interactions (cont’d)
Note 3:The display is changed depending on the specification of ACIS.
Note 4:Has priority over the FLEXIBLE ROUTING - FCCS service. FLEXIBLE ROUTING - FCCS is activated only when
the FCCS trunk for the destination station is busy.
Note 5:A trunk is used after the call encounters station busy between the stations in the FCCS network.
Note 6:Available only at the time of the data...