NEC Neax 2000 Ivs2 Wcs System Manual

CHAPTER 3 SYSTEM DATA PROGRAMMING
PS Data Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 53
PS DATA PROGRAMMING
Perform the following procedure after completing SYS ID Assignment and ZT Authorization.
DESCRIPTION DATA
Assign a PS station No. to the required
vir tual PS LEN.
NOTE 1:When the Expansion Memory
card (PZ-M537) is not mounted
on the MP card, the 1st data is
000-127.
NOTE 2:For Roaming PS, max. 5 digits
PS station number should be
assigned.(1)
(2)000-255 : Virtual PS...

NEAX2000 IVS2WCS System Manual (PCS)Page 54ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
PS Data Programming
DESCRIPTION DATA
Assign the Service Restriction Class to
each PS station.
(1)
(2)YY=02
X-XXXXXXXX : PS station No.
XX ZZ
XX : Service Restriction
Class A (00-15 )
When providing Roaming service, specify
the Service Restriction Class for Roaming
service data download.
NOTE 1:Assign the same Service
Restriction Class data to the PS
station number and the Vi rtual
LC station number
(For...

CHAPTER 3 SYSTEM DATA PROGRAMMING
PS Data Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 55
 When changing the PS operation data
If you change the PS operation data in this section which hasbeen already downloaded to a PS,
do PS data download (CM1D YY=20 second data: 1) again.
DESCRIPTION DATA
Download the PS operation data to each
PS by assigning the 2nd data 1.
(1)
(2)YY=20
X-XXXXXXXX : PS station No.
1 : To be executed
Refer to “D
termPS User Manual”.
NOTE 1:All steps for...

NEAX2000 IVS2WCS System Manual (PCS)Page 56ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Virtual Line/Trunk Data Programming (For Integrated/Adjunct CCIS)
VIRTUAL LINE/TRUNK DATA PROGRAMMING
(FOR INTEGRATED/ADJUNCT CCIS)
This programming is required for Integrated Type or Adjunct Type (CCIS Interface).
DESCRIPTION DATA
Assign a vir tual station number to the
required LEN.
NOTE 1:The Vir tual LEN must be as-
signed from the last LEN 763.
NOTE 2:Do not assign the same station
No. to the Vir...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Virtual Line/Trunk Data Programming (For Integrated/Adjunct CCIS)
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 57
DESCRIPTION DATA
The following data is set automatically by the virtual line-trunk path setting of CM5A YY=00.
If you clear CM5A YY=00 setting data, the following data is also cleared automatically.
NOTE:The trunk route data must be assigned by CM35because the trunk route data is
not automatically assigned.
The trunk route of the Virtual...

NEAX2000 IVS2WCS System Manual (PCS)Page 58ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Virtual Line/Trunk Data Programming (For Integrated/Adjunct CCIS)
DESCRIPTION DATA
Change the trunk route for the vir tual trunk
number, if required.
(1)
(2)YY=00
256-511: Virtual Trunk No.
00-63 : Trunk No.
Assign the data for the Virtual Line/Trunk
to the trunk route No. assigned by CM30
YY=00.
(1)
(2)YY=00 (Kind of Route)
00-63 : Trunk Route No.
00 : DDD

(1)
(2)YY=01 (Type of Signal)
00-63 : Trunk...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Trunk Data Programming (For Adjunct Analog)
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 59
TRUNK DATA PROGRAMMING (FOR ADJUNCT ANALOG)
This programming is required for Adjunct Type (Analog Interface).
DESCRIPTION DATA
Assign a trunk number to the required
LEN.(1)
(2)000-763 : LEN
0-7 (PIM0-7) +
00-63 (Port No.)
D000-D255 : Trunk No.
Assign the trunk route number to the trunk
number.
(1)
(2)YY=00 (DP or DTMF)
000-255: Trunk No.
00-63 : Trunk Route No....

NEAX2000 IVS2WCS System Manual (PCS)Page 60ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Trunk Data Programming (For Adjunct Analog)
DESCRIPTION DATA
Specify the answer signal from the distant
office for outgoing connection to the trunk
route.
(1)
(2)YY=04
00-63 : Trunk Route No.
1 : Battery Reversal
7 : Answer signal does not arrive
from C.O. Line (Answer timing
shall be set by CM41 Y=0
Function No. 03)
Specify the release signal from the distant
office for an outgoing connection of an...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Trunk Data Programming (For Adjunct Analog)
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 61
DESCRIPTION DATA
Specify the Sender prepause timing to the
trunk route.
NOTE:To reduce the connecting time, it
is preferable to shor ten the
prepause timing (i.e., second
data=03 (1.5 sec.))
(1)
(2)YY=21
00-63: Trunk Route No.
00: 0 sec. 08 : 6.0 sec.
01: 0.5 sec. 09 : 7.0 sec.
02: 1.0 sec. 10 : 8.0 sec.
03: 1.5 sec. 11 : 9.0 sec.
04: 2.0 sec. 12 : 10.0 sec.
05:...

NEAX2000 IVS2WCS System Manual (PCS)Page 62ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Trunk Data Programming (For Adjunct Analog)
DESCRIPTION DATA
Specify the DP Make Ratio.
(1)
(2)YY=25
00-63 : Trunk Route No.
0 : 39 % Make Ratio
1 : 33 % Make Ratio
Assign the DTMF signal width to the trunk
route.
NOTE:To reduce the connecting time, it
is recommended to shorten the
DTMF inter-digital Pause timing
(YY=24), i.e., second data=2 (80
ms). YY=26, i.e., second data=0
(64 ms).
(1)
(2)YY=26...