NEC Neax 2000 Ivs2 Wcs System Manual

CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 83
DESCRIPTION DATA
Specify the order of LCR selection for the
Route Pattern No. assigned by
YYYY=4000-4007.
(1)
(2)YYYY=0000-0255
(Route Pattern No. 000-255)
1-4: Order of LCR Selection
1: 1st
2: 2nd
3: 3rd
4: 4th
XXX ZZ
XXX: 000-255
(LCR Pattern No. 000-255)
ZZ: 00-63 (Trunk Route No. 00-63)
To delete the designated digit of an area
code:
(1)
(2)YYYY=5000-5255
153...

NEAX2000 IVS2WCS System Manual (PCS)Page 84ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
DESCRIPTION DATA
Specify the maximum number of digits to
be dialed by the calling pa rty.
The maximum number of digits including
the area codes should be assigned to
each area code.
(1)
(2)Y=0-7 (Area Code Development
Pattern No. 0-7 assigned by CM8A,
Y=A00)
X-X...X (Area Code dialed, Max. 8
digits)
01 : 1 digit
24 : 24 digits
79 : 79 digits
END
B
CM85
||
|| 

CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 85
Q931a Digital Trunk Data Programming
 DTI Assignment
DESCRIPTION DATA
Assign an AP number to the DTI card.
The AP number must match the SENS
switch setting on the DTI card.
(1)
(2)Y=0
04-15, 20-31: AP No.
09: DTI card
Assign the trunk number to each channel
number on the DTI card.
NOTE:The system allocates time slots
to consecutive channels from
lowest to highest channel...

NEAX2000 IVS2WCS System Manual (PCS)Page 86ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
DESCRIPTION DATA
Assign a Trunk Route to each trunk
number used for voice channel (B
channel), and also to signaling channel (D
channel). Make a separate route for B
channels and D channels.
NOTE:DTI route must be separated
from analog trunk
routes

(1)
(2)YY=00
000-255: B Channel, D channel Trunk
No. assigned by CM07 YY=01
00-63: Trunk Route No.
Assign the terminating...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 87
DESCRIPTION DATA
Assign trunk route data to each channel
trunk route number assigned by CM30
YY=00.
(1)
(2)YY=00 (Kind ofTrunk Route)
00-63: B Channel, D Channel Route No.
04: Tie Line

(1)
(2)YY=01 (Dialing Signal Type)
00-63: B Channel Route No.
7 : Call Termination; DP/DTMF
Call Origination; DTMF

(1)
(2)YY=04
(Answer Signal from Distant Office)
00-63: B Channel Route...

NEAX2000 IVS2WCS System Manual (PCS)Page 88ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
DESCRIPTION DATA
T/R: Transmitter PAD/Receiver PAD
+: Gain
–: Loss
(1)
(2)YY=19
00-63: B Channel Route No.
0:
1 : Programmable PAD
2: (SeeCM42)
3:
4:
5: FixedPAD
6 : (See left table)
7:
When using the programmablePAD
(CM35 YY=19, 2nd Data=0-3), assign the
PAD data.(1)
(2)50-65
00-15
T/R: Transmitter PAD/Receiver PAD
+: Gain
–: Loss
CM35
C
CM42
D
CONNECTION...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 89
 DCH Assignment
DESCRIPTION DATA
Assign an AP number to the DCH card
(PN-SC01).
The AP number must match the SENS
switch setting on the DCH card.
(1)
(2)Y=0
04-15, 20-31: AP No.
35: DCH for Roaming
Assign the DCH number to the AP number
of DCH assigned by CM05.
(1)
(2)YY=08
0-7: DCH No.
04-15, 20-31: AP No. assigned by
CM05
Execute CM35 YY=90 for the B channel
route and D...

NEAX2000 IVS2WCS System Manual (PCS)Page 90ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
DESCRIPTION DATA
Specify the LAPD Mode of the D channel
route as “Network Mode” or “User Mode”.
This data must be set differently between
the opposite DTIs. When the opposite
office is a master office, set this data to 1
(User Mode), and when the opposite office
isaslaveoffice,setthisdatato0(Network
Mode).
(1)
(2)YYY=113 (LAPD Mode)
00-63: D Channel Route No.
0:NetworkMode...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 91
Home PS Data Programming
DESCRIPTION DATA
Assign an AP number to the DBM (Data
Base Module) card (PN-AP00-A).
The AP number must match the SENSE
switch setting of the card.
(1)
(2)Y=0
04-15: AP No.
34: DBM (AP00-A) for Roaming
Assign the Trunk Restriction Class for
Home PS. This data is sent to the visitor
PBX when the PS is roaming.
NOTE 1:When the location registration of
a...

NEAX2000 IVS2WCS System Manual (PCS)Page 92ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
DESCRIPTION DATA
Assign the Tenant number to the Home
PS. This data is sent to the visitor PBX
when the PS is roaming.
NOTE 3:It is recommended to assign the
PS station (CM1C) and its
related virtual LC station number
to the same service restriction
class when roaming is provided.
SeePS Data Programming on
Page 53
(1)
(2)YY=04 (Service Restriction Class)
X-XXXXXXXX: Virtual...