NEC Neax 2000 Ivs2 Wcs System Manual

CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 93
Visitor PS Data Programming
DESCRIPTION DATA
Execute System Data Memory All Clear of
the DBM (PN-AP00-A) card.
The System Data Memory All Clear must
be done at theinitial setup.
This data is valid when the DBM card is
on-line.
(1)
(2)YYY=999
1(AllClear)
CCC
Execute Work Memory All Clear of the
DBM card.
The Work Memory All Clear must be done
before the system star ts...

NEAX2000 IVS2WCS System Manual (PCS)Page 94ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
DESCRIPTION DATA
Assign the Trunk Route to be used for
requesting the data of the Visitor PS
against its Home PBX.
This data is valid when the DBM card is
on-line.
(1)
(2)YYY=100-107
(Route Selection Pattern No. 00-07)
1-4: First-Fourth Selected Route
00-63 : Q931a D ChannelTrunk
Route No.
NONE : No Data
CCC : No Data Clear
Assign the default restriction class for
Visitor...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 95
DESCRIPTION DATA
Specify a path between the virtual line and
virtual trunk.
(1)
(2)YY=00
256-511: Virtual Trunk No.
NOTE 1,NOTE 2
X-XXXX: Virtual Station No.
The following data are set automatically by the virtual line-trunk path setting of CM5A
YY=00. If you clear CM5A YY=00 setting data, the following data are also cleared
automatically.
CM5A
B
C
COMMAND
CODE MEANINGS 1ST...

NEAX2000 IVS2WCS System Manual (PCS)Page 96ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
DESCRIPTION DATA
NOTE 1:PS station No. is assigned by the first data of CM1C (Virtual PS LEN) as follows.
Virtual PS LEN=Virtual Trunk No. minus 256
For example, when the Vir tual Trunk No. is 256 (CM5A YY=00 1st data: 256), then
the Vir tual PS LEN is 000 (CM1C 1st data: 000).
NOTE 2:When the Expansion Memory card (PZ-M537) is not mounted on the MP card, the
first data is...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 97
DESCRIPTION DATA
Assign the Service Restriction Class of the
Virtual LC for the Visitor PS.
Assign the different class to the Virtual LC
for Visitor PSs from the station and Home
PS of the PBX.
(1)
(2)YY=02
X-XXXX: Virtual LC station No.
XX YY
XX: Service Restriction Class A
(00-15 )
YY: Service Restriction Class B
(00-15 )
Assign the Service Restriction Class C of
the Vir...

NEAX2000 IVS2WCS System Manual (PCS)Page 98ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
DESCRIPTION DATA
Assign trunk route data to the Virtual COT
route number for the visitor PS assigned
by CM30 YY=00.
(1)
(2)YY=00 (Kind ofTrunk Route)
00-63 : Route No.
00: ISDN/C.O. Trunk

(1)
(2)YY=01 (Dialing Signal Type)
00-63 : Route No.
4 : Call Termination; DTMF
Call Origination; DTMF
7 : Call Termination; DP/DTMF
Call Origination; DTMF

(1)
(2)YY=04
(Answer Signal...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 99
DESCRIPTION DATA
Specify the Route Selection Pattern Num-
ber as “Pattern Number 0”, for all classes
of the Trunk Restriction Class (01-06) sent
from the Home PBX.
This data is valid when the DBM card is
on-line.
(1)
(2)YYY=208
01-06 : Trunk Restriction Class sent
from the Home PBX
00 : Route Selection Pattern 0
Specify the Virtual COT trunk route to be
used for...

NEAX2000 IVS2WCS System Manual (PCS)Page 100ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
DESCRIPTION DATA
Provide the Visitor PS with the capability to
enter an Account Code, if required.
(1)
(2)YY=30
00-15 (Service Restriction Class A
assigned by CM12 YY=02)
0 : Restricted
1:Allowed
Specify the maximum number of Account
Code.(1)
(2)10 (Max. digits for Account Code)
01-16 : 01-16 digitsG
CM15
END
CM42 

CHAPTER 3 SYSTEM DATA PROGRAMMING
Maintenance Data Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 101
MAINTENANCE DATA PROGRAMMING
DESCRIPTION DATA
Assign the registration of fault information
into Memory and the control of the
external alarm.
(1)
(2)Y=2
12 : ZT fault occurred
2B : ZT fault occurred
3B : ZT fault recovered
0 : Registration of fault memory
No output of External alarm
1 : Registration of fault memory
External alarm is MN alarm
2 : Registration of fault memory...

NEAX2000 IVS2WCS System Manual (PCS)Page 102ND-70920 (E), Issue 1.0
This page is for your notes.