NEC Neax 2000 Ivs2 Wcs System Manual

CHAPTER 3 SYSTEM DATA PROGRAMMING
Progamming Summary
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 43
PROGAMMING SUMMARY
Perform the system data programming related to the WCS according to the following procedure.
For other system data related to the PBX, refer to the Command Manual and the CCIS System
Manual.
Initial Setup of System
V I RT UA L L I N E / T RU N K DATA
PROGRAMMING
END
ZT AUTHORIZATION
PS DATA PROGRAMMING
Adjunct System (CCIS Interface) Integrated System
WCS FEATURE...

NEAX2000 IVS2WCS System Manual (PCS)Page 44ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Progamming Summary
Changing ZT Data in Service
When you change the ZT data (CM10, CM06, CMAD, CMAE) in service, make busy of the ZT is
required. In this case, do the following procedure.
NOTE:To make busy or make idle the ZT in service, assign data as follows:
CME5 Y=3
(1) 000-127: ZT No.
(2) 1: Make idle
2: Make busy after calls finished.
START
END
CHANGE OF ZT DATA?
NO YES
CHANGE OF ZT DATA
(CM10, CM06,...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Progamming Summary
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 45
Changing PS Data
If you change the PS data which has been already downloaded to a PS, do PS data download
again by CM1D.
CM1D YY=20
(1) X-XXXXXXXX: PS station No.
(2) 1
Replacing PS
When replacing the PS with a new one, moreover assigning the same PS number to the new PS,
delete the PS number registered to the WCS by CM1C is required before downloading the new
PS data.
CM1C
(1) 000-255:...

NEAX2000 IVS2WCS System Manual (PCS)Page 46ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
ZT Data Programming
ZT DATA PROGRAMMING
Initial Setup
DESCRIPTION DATA
Assign an AP number to the CSH card.
The AP number must match the SENSE
switch settings on the CSH card.
(1)
(2)Y=0
04-15, 20-31: AP No.
23: CSH (PN-SC03-A) card
Assign a ZT number to the required LEN.
NOTE:The ZT number must be
assigned to the first LEN (Level
0) and/or second LEN (Level 2)
of each LT slot.(1)
(2)000-763: LEN
0-7...

CHAPTER 3 SYSTEM DATA PROGRAMMING
ZT Data Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 47
DESCRIPTION DATA
Assign an area to be called to eachZT.
NOTE:Confirm that the busy LED lamp
on CSI card is flashing (60 IPM).
(1)
(2)YY=00
000-127 : ZT No.
XX Y ZZ
XX : 00-31 (Calling Area No.)
Y : 0-7 (Group No.)
ZZ : 00-31 (Group ZT No.)
NONE : No data
CCC : Data Clear
Specify the type of ZT. 
(1)
(2)YY=19
000-127 : ZT No.
00 : D
termPS II Type
15 : Previous DtermPS Type
Assign a PAD...

NEAX2000 IVS2WCS System Manual (PCS)Page 48ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
ZT Data Programming
DESCRIPTION DATA
Specify the Nation Code. 
(1)
(2)YY=00
03 (Nation Code Assignment)
003 : North America 310
004 : North America 311
005 : North America 312
006 : North America 313
007 : North America 314
008 : North America 315
009 : North America 316
255 : Not used
When providing Roaming service, assign
the Network ID.
(1)
(2)YY=42
00 (Network ID Assignment)
00000-65534 : Network...

CHAPTER 3 SYSTEM DATA PROGRAMMING
ZT Data Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 49
Changing ZT Data in Service
When you change the ZT data (CM10, CM06, CMAD, CMAE) in service, make busy of the ZT is
required.
When you change the ZT number by CM10, ZT authorization is required by NTAC or LVP Server
entry.
DESCRIPTIONDATA
Assign a Control Carrier Information.
NOTE 1:Set 1st priority to the 5th priority
(10 digits).
NOTE 2:Select the Control Carrier No. as
follows:
Fo r...

NEAX2000 IVS2WCS System Manual (PCS)Page 50ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
ZT Data Programming
DESCRIPTION DATA
Make the ZT busy. 
(1)
(2)Y=3
000-127 : ZT No.
2 : Make busy after calls
finished.
Make the ZT idle. 
(1)
(2)Y=3
000-127 : ZT No.
1:MakeIdle
CM10
CM06
CMAD START
END
CME5
CMAE
CME5Change the ZT data.
SeeInitial Setup on
Pa ge 4 6 

CHAPTER 3 SYSTEM DATA PROGRAMMING
ZT Authorization
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 51
ZT AUTHORIZATION
Initial Setup of ZT
Do the following procedure to set up the ZT.
NOTE:When re-installing the system after power down exceeding 8 hours, the System ID will
be cleared. The System ID must be re-entered.
START
ZT DATA PROGRAMMING
ZT AUTHORIZATION
SYS ID ASSIGNMENTASSIGNMENT OF
LVP CODE
END ZT AUTHORIZATION
NTAC LV P
Pag e 46
Call NTAC or enter
the System ID code
on MATWorX...

NEAX2000 IVS2WCS System Manual (PCS)Page 52ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
ZT Authorization
Setting Up of Additional ZT
Do the following procedure to add the ZT.
START
ZT DATA PROGRAMMING
ZT AUTHORIZATION
END
See MATWorX Studio.Pag e 46
Please call NTAC (National Technical Assistance
Center) for this data assignment. Action by Maintenance Person :
: