NEC Neax 2000 Ivs2 Wcs System Manual

CHAPTER 2 INSTALLATION
Mounting CSI Card
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 33
MOUNTING CSI CARD
(1) Before mounting the CSI (PN-2CSIA) card, confirm the correct switch settings.
SeeCHAPTER 4.
(2) Mount the CSI card in the LT slots of PIM0 though PIM7.
PIM0-7: LT00-LT07 slotsATTENTIONContents
Static SensitiveHa ndl ing
Prec au tio ns Requ ired 

NEAX2000 IVS2WCS System Manual (PCS)Page 34ND-70920 (E), Issue 1.0
CHAPTER 2 INSTALLATION
Connection of ZT
CONNECTION OF ZT
Connect the cable to a ZT via the MDF as described in this section.
 Location ofLT slots andLTC connectors for ZT (Figure 2-1)
 MDF Cross connection for ZT (Figure 2-2)
Figure 2-1 Location of LT Slots and LTC Connectors for ZT
LT C 0
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25RA0
TA 0
RA1
TA 1
RA0
TA 0
RA1
TA 1
RA0
TA 0
RA1
TA 1
MJRB0
TB0
RB1
TB1...

CHAPTER 2 INSTALLATION
Connection of ZT
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 35
Figure 2-2 MDF Cross Connection for ZT
CAUTION: Incorrect wiring may cause severe damage to the equipment.
 









PBX
(PIM0-7)
BWB
CSI
TWISTED-PAIR
CABLEMDF
LTC0/LTC1/LTC2 CONNECTORModular
Connector
To Z T
1RA0 26RB0
2TA0 27TB0
3RA1 28RB1
4TA1 29TB1
5RA2 30RB2
6TA2 31TB2
7RA3 32RB3
8TA3 33TB3
934
10 35
11 36
12 37
13 38
14 39
15 40
16 41
17 42
18 43
19 44
20 45
21 46
22 47
23 48
24 49
25 50
ZT No....

NEAX2000 IVS2WCS System Manual (PCS)Page 36ND-70920 (E), Issue 1.0
CHAPTER 2 INSTALLATION
Connection of ZT
Figure 2-3 MDF Cross Connection via MDF for ZT
12
3
4
5
6
7 8
Modular
Connector
(8)(1)
NOTE:RJ-45 Modular Jack is highly recommended.
Keep all wiring straight to the jack and perform all reverses at the cross connect for
future changes.
TERMINAL
NUMBERCOLORTERMINAL
NUMBERFUNCTION POLARITY
CSI
TERMINAL TERMINAL
EQUIPMENTCSI SIGNAL FEED
1 blue a Not used Not used
2 orange b Not used Not used
3 black c...

CHAPTER 2 INSTALLATION
Installation for Multi-Site Roaming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 37
INSTALLATION FOR MULTI-SITE ROAMING
(1) Before mounting the DTI (PN-24DTA/PN-30DTC), DCH (PN-SC01), DBM (PN-AP00-A)
card, set the MB switch to UP position, and set the other switches to appropriate position.
SeeCHAPTER 4.
(2) Mount the DTI, DCH, DBM card in AP slots of PIM0 though PIM7.
PIM0-7: AP00-AP11 slots
(3) After mounting the card, set the MB switch to DOWN position to put...

NEAX2000 IVS2WCS System Manual (PCS)Page 38ND-70920 (E), Issue 1.0
CHAPTER 2 INSTALLATION
Installation for Multi-Site Roaming
Figure 2-5 Location of AP Slots and LTC Connectors for DTI
LT C 0
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25RA
TA
RA
TA
RA
TA
MJRB
TB
RB
TB
RB
TB
MNRA
TA
RA
TA
RA
TARB
TB
RB
TB
RB
TBRA
TA
RA
TA
RA
TARB
TB
RB
TB
RB
TBRA
TA
RA
TA
RA
TARB
TB
RB
TB
RB
TB 26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
AP00
SLOT
AP01
SLOT
AP02...

CHAPTER 2 INSTALLATION
Installation for Multi-Site Roaming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 39
Figure 2-6 Example of MDF Cross Connection for DTI
PIM 0
JP MDF PN-24DTA/PN-30DTC
AP05
RA
RB
TA
TB17
42
18
4317
42
18
43RA
RB
TA
TBTO CSU LT C 1
RECEIVE
TRANSFER
17
18
19
20RA
TA42
43
44
45RB
TB LT C 1 ( J )42
43
44
45RB
TB17
18
19
20RA
TA LT C 1 ( P ) 

NEAX2000 IVS2WCS System Manual (PCS)Page 40ND-70920 (E), Issue 1.0
This page is for your notes. 

NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 41
CHAPTER 3
SYSTEM DATA
PROGRAMMING
This chapter explains the programming procedure to provide the WCS
feature to the PBX. 

NEAX2000 IVS2WCS System Manual (PCS)Page 42ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
How to Read This Chapter
HOW TO READ THIS CHAPTER
In the programming procedure, the meaning of (1), (2), and markings are as follows.
(1) : 1st Data
(2) : 2nd Data
: Initial Data
With the system data clear command (CM00, CM01), the data with this marking is automatically
assigned for each command.
: A reset of the MP card is required after data setting.
Press SW1 switch on the MP card.
: A reset of the...