NEC Neax 2000 Ivs2 Isdn System Manual

 NEAX2000 IVS2 ISDN System ManualPage 130  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Event Based CCIS Programming
• To connect the ISDN line for the voice channel after the called party answers, do the
following programming.
By the following programming, the ISDN line for the voice channel is not connected, until the
called par ty answers, or when the called par ty does not answers the call.
NOTE:This feature is available only for the connection between the NEAX2000 IVS
2/7400ICS...

CHAPTER 3  SYSTEM DATA PROGRAMMING
Event Based CCIS Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 131
Incoming Termination for Event Based CCIS Calls
DESCRIPTION DATA
Assign the Number Conversion Block No.•
(1)
(2)YY=00
X-XXXX: DID No.
000-999: Number Conversion Block 
No. 0-999
Conver t received digits to Mate-Side 
trunks.



(1)
(2)YY=01 Day Mode
YY=02 Night Mode
YY=03 Mode A
YY=04 Mode B
000-999: Number Conversion Block 
No. assigned by CM76 Y=00...

 NEAX2000 IVS2 ISDN System ManualPage 132  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Event Based CCIS Programming
Access Code/Terminating Number Assignment 
for Outgoing Event Based Calls
DESCRIPTION DATA
Allocate memory to store the terminating 
numbers to the opposite office. (1)
(2)66
XXX YYY
XXX: 000-299: First Memory Slot No.
YYY: 001-016: Number of Memory Slot 
allocated
Assign terminating numbers of the 
opposite office (access code for ISDN line 
+ ISDN subscriber number) to the...

CHAPTER 3  SYSTEM DATA PROGRAMMING
Event Based CCIS Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 133
Release Timer for Virtual Tie Lines 
(Home-Side and Mate-Side Trunks)
DESCRIPTION DATA
Specify the release timer for voice 
channels of virtual tie line. If there are no 
calls for predetermined time, the voice 
channels used for Event Based CCIS is 
released.
(1)
(2)Y=0
87: Virtual Tie Line Release Timer
    for Voice Channels
02: 2.4-4.8 sec. (2.4 sec. increments)
30:...

 NEAX2000 IVS2 ISDN System ManualPage 134  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Event Based CCIS Programming
CCH Data Assignment 
DESCRIPTION DATA
Assign an AP number to the CCH card 
(PN-SC00).
The AP number must match the SENSE 
switch setting on the CCH card.
(1)
(2)Y=0
04-15, 20-31: AP No.
11: CCH Card
Assign a CCH channel number to each 
CCH card.
(1)
(2)YY=07
0-7: CCH channel No.
04-15, 20-31: AP No. of CCH Card
Assign the trunk number used as the 
common signaling...

CHAPTER 3  SYSTEM DATA PROGRAMMING
Event Based CCIS Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 135
Tandem Connection Programming
 When providing Tandem Connection (ISDN to CCIS/CCIS to ISDN), do the following
programming:
DESCRIPTION DATA
 Specify the combination of trunk routes 
allowing the tandem connection.
NOTE:The Home-Side Virtual Tie line 
routes must be included for all 
Tandem combinations.
(1)
(2)Y=0
XX ZZ
XX: 00-63: Incoming Trunk Route
ZZ: 00-63:...

 NEAX2000 IVS2 ISDN System ManualPage 136  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Event Based CCIS Programming
Closed Numbering Plan Programming
DESCRIPTION DATA
Assign LCR Group number to Area Code 
Development Pattern.
(1)
(2)YYYY=A000
0-3: LCR Group No.
4000-4007: Area Code Development 
Pattern No.
Assign Area Code Development Pattern 
number.
(1)
(2)YYYY=4000-4007
X...XXX: Area Code (Max. 8 digits)
0000-0255: Route Pattern No.
Assign Route Pattern.
(1)
(2)YYYY=0000-0255
1-4:...

NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 137
CHAPTER 4
CIRCUIT CARD 
INFORMATION
This chapter explains the mounting location, the meaning of lamp
indications, and the method of switch settings of each circuit card for
the ISDN system. 

 NEAX2000 IVS2 ISDN System ManualPage 138  ND-70919 (E), Issue 1.0
CHAPTER 4  CIRCUIT CARD INFORMATION
How to Read This Chapter
HOW TO READ THIS CHAPTER
This chapter explains each circuit card used in this system. Explanations are given in
alphabetical order of the circuit card names within each circuit card category (Control,
Application Processor, and Line/Trunk).
(1) Locations of Lamps, Switches, and Connectors
The locations of lamps, switches, and connectors of each circuit card are shown by a face...

CHAPTER 4  CIRCUIT CARD INFORMATION
Mounting Location of Circuit Card
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 139
MOUNTING LOCATION OF CIRCUIT CARD
This section explains the conditions for mounting circuit cards for the ISDN system. Figure 4-1
shows circuit card mounting slots allocated in the PIM.
Figure 4-1  Mounting Location of Circuit Card
*1: PN-CP14 (MP) card on the MP12 slot on PIM0.
*2: The following application processor cards can be mounted in the AP00-AP11 slots on...