NEC Neax 2000 Ivs2 Isdn System Manual

 NEAX2000 IVS2 ISDN System ManualPage 90  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Feature Programming
Trunk Provisioning Service Selection
DESCRIPTION DATA
Assign the trunk route to the trunk number 
assigned by CM07.
(1)
(2)YY=00 Trunk Route Allocation
000-255: Trunk No. assigned by CM07 
YY=01.
00-63: Route No.START
CM30
END 

CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Feature Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 91
ISDN PRI Call By Call Service Selection
[North America Only]
Available Services
The following Binary Facility Code can be sent to the ISDN network when the called party number
is flagged as a Service. Services and features are selected by the ISDN subscriber at the time
the ISDN is ordered. The PBX must be programmed to match the services and features provided
by the ISDN...

 NEAX2000 IVS2 ISDN System ManualPage 92  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Feature Programming
The next example details a local 7 digit call and will not used a Binary Facility Code.
CM8A4005>2 (dialed number)=001 (go to route pattern 000)
CM8A0000>1 (1
st choice)=00210 (use LCR pattern 002 + trk route 10)
CM855>2=7 (maximum number of digits dialed)
CM8A5002>157=04 (Kind of called party=Local) (dialed number is 7-digit NANP, select Local)
CM8A5002>158=01 (Called party...

CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Feature Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 93
Required Network Information
Four components are required by the network when sending CIC information. This information
can be found in the SETUP message.
(1) FEATURE (A statement advising the network that this is a feature based call, as opposed 
to a Service based call).
(2) TYPE OF NETWORK ID (The PBX should send out NATIONAL for this information).
(3) NETWORK ID PLAN...

 NEAX2000 IVS2 ISDN System ManualPage 94  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Feature Programming
DESCRIPTION DATA
Assign the kind of the called party number.
(1)
(2)YYYY=5000-5255 
LCR/TR Pattern No. 000-255
157: Kind of Called Party No.
01 : International
02 : National
03 : Network
04 : Local
05 : Not used
06 : Speed Dial
NONE : No data
Assign the Called Par ty Numbering Plan 
Identifier.
(1)
(2)YYYY=5000-5255 
LCR/TR Pattern No. 000-255
158: Called Party Numbering Plan...

CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Feature Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 95
DESCRIPTION DATA
Assign the Network ID Plan number.
(1)
(2)YYYY=5000-5255 
LCR/TR Pattern No. 000-255
160: Network ID Plan
00-15 : Network ID Plan No.
NONE : No data
Assign the Network ID character.
(1)
(2)YYYY=5000-5255 
LCR/TR Pattern No. 000-255
161: Network ID Character
X-XXX: X=0-9, A (*), B (#)
Specify whether Call By Call is Feature or 
Service.
(1)...

 NEAX2000 IVS2 ISDN System ManualPage 96  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Feature Programming
DESCRIPTION DATA
Assign the WATS Band number.
(1)
(2)YYYY=5000-5255 
LCR/TR Pattern No. 000-255
164: WATS Band No.
00-09 : WATS Band No.
NONE : No data
END
CM8A
B 

CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Feature Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 97
Advice of Charge (AOC)
[Australia/France Only]
NOTE:When you require Call Recording of ISDN call, do the data programming for SMDR or
CIS. For details, refer to the Feature Programming Manual.
DESCRIPTION DATA
Specify the Advice of Charge (AOC) 
display on D
term when the charge total is 
over $9999.99.
(After 6 sec., the display goes off.)(1)
(2)402
0 : Flashing display
1 :...

 NEAX2000 IVS2 ISDN System ManualPage 98  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Feature Programming
Centrex SHF Over ISDN
[N.Z. Only]
To send hooking signal from a D
term to a main PBX via ISDN, do the following programming:
DESCRIPTION DATA
Provide the voice channel trunk route for 
the main PBX with the Centrex function.
(1)
(2)YY=86
00-63: B channel Trunk Route No.
0: To provide
Assign the SHF Key on the D
term.
(1)
(2)YY=00
My Line No. +   + Key No.
F1009: SHF (Hooking...

CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-VPN Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 99
ISDN-VPN PROGRAMMING
DESCRIPTION DATA
Assign the access code for LCR Group 0-
3.
(1)
(2)Y=0-3 Number Plan Group 0-3
X-XXXX: Access Code
A126: LCR Group 0
A127: LCR Group 1
A128: LCR Group 2
A129: LCR Group 3
Assign the LCR Group key on the D
term, if 
required.
(1)
(2)YY=00
My Line No. +   + Key No.
F0A26: LCR Group 0
F0A27: LCR Group 1
F0A28: LCR Group 2
Assign an Area Code...