NEC Neax 2000 Ivs2 Isdn System Manual

 NEAX2000 IVS2 ISDN System ManualPage 60  ND-70919 (E), Issue 1.0
CHAPTER 2  INSTALLATION
Installation Procedure for ISDN Terminal
Figure 2-15  Example of MDF Cross Connection for ILC
1
2
3
4
5
6
7 8
Pin No.
LT 0 0PIM0
ILC J PLT C 0
RA0
TB1 RB1
TB0
RB0
TA 0
RA1
TA 11
29 28
27
26
2
3
41
29 28
27
26
2
3
4
MDF
RA
RB
TA
TB RECEIVE
SEND3
6
4
5TO ISDN
TERMINAL
1RA26RBLT C  ( J )
2TA27TB
328
429
26 RB 1 RA
27 TB 2 TA
28 3
29 4
Pin No. PBX Direction of Signal Terminal
1
2
3RA←TA
4TA→RA
5TB→RB
6RB←TB
7
8Not Used...

CHAPTER 2  INSTALLATION
Installation Procedure for Event Based CCIS
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 61
INSTALLATION PROCEDURE FOR EVENT BASED CCIS
Install the equipment for Event Based CCIS according to the procedure shown in Figure 2-16.
NOTE:For Call Recording of ISDN call, install the equipment for SMDR/CIS. For details, refer
to the Installation Procedure Manual.
Figure 2-16  Installation Procedure for Event Based CCIS
END START
Mounting 
PRT Card or BRT Card...

 NEAX2000 IVS2 ISDN System ManualPage 62  ND-70919 (E), Issue 1.0
CHAPTER 2  INSTALLATION
Installation Procedure for Event Based CCIS
Mounting CCH Card
(1) Before mounting the CCH (PN-SC00) card, set the MB switch to UP 
position, and set the other switches to appropriate position.
See CHAPTER 4.
(2) Mount the CCH card in the following AP slots:
PIM0-7: AP00-AP11
The AP11 slot on PIM0 is available only when the FP card is not mounted in the FP11 slot 
on PIM0.
(3) After mounting the card, set the MB...

NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 63
CHAPTER 3
SYSTEM DATA 
PROGRAMMING
This chapter explains the programming procedure to provide the ISDN
feature to the PBX. 

 NEAX2000 IVS2 ISDN System ManualPage 64  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
How to Read This Chapter
HOW TO READ THIS CHAPTER
In the programming procedure, the meaning of (1), (2), and markings are as follows:
(1) : 1st Data
(2) : 2nd Data
: Initial Data
With the system data clear command (CM00, CM01), the data with this marking is
automatically assigned for each command.
: System Initialization
A reset of the MP card is required after data setting.
Press SW1 switch on the MP...

CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-PRI Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 65
ISDN-PRI PROGRAMMING
Digital Trunk Data Assignment
DESCRIPTION DATA
Assign an AP number to the DTI/PRT 
card. 
The AP number must match the SENSE 
switch setting on the DTI/PRT card.
(1)
(2)Y=0
04-15, 20-31: AP No.
09: DTI card
12: PRT card
Specify the AP highway channel for 24DTI/
PRT card.
(1)
(2)Y=1
04-15, 20-31: AP No.
0 : Expanded Highway channel 
(128 time slots)
1 :...

 NEAX2000 IVS2 ISDN System ManualPage 66  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-PRI Programming
DESCRIPTION DATA
Assign the necessary functions to the DTI/
PRT card. CMAA YY=00/01/02 assign-
ment is required only for 24DTI/PRT.
After entering the data, set the MB switch 
on the DTI/PRT card to UP, and then to 
DOWN, for DTI/PRT initialization.
NOTE:The following table shows the 
relationship between CMAA 
YY=01 and YY=02.
(1)
(2)

(1)
(2)

(1)
(2)

(1)
(2)YY=00 Data Mode...

CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-PRI Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 67
DESCRIPTION DATA
Assign Circuit Identification Code (CIC) 
number to each ISDN trunk used for voice 
channel only.
NOTE:CIC No. must not be assigned to 
the trunk No. of D channel: TS16 
(30DTI) or TS23 (24DTI/PRT).
(1)
(2)YY=07
000-255: Trunk No. assigned by CM07 
YY=01
000-029: CIC No.
EXAMPLE OF 30DTI
B channel trunk No.: D100-D114, D116-
D130
D channel trunk No.: D115
(1)...

 NEAX2000 IVS2 ISDN System ManualPage 68  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-PRI Programming
DESCRIPTION DATA

(1)
(2)YY=05 
Release Signal from distant office
00-63: B channel/D channel Trunk 
Route No.
1 : Release signal arrives 
NOTE 2

(1)
(2)
(1)
(2)YY=09 Incoming Connection Signaling
00-63: B channel Trunk Route No.
08: ISDN
00-63: D channel Trunk Route No.
15 : Not used

(1)
(2)YY=11 Toll Restriction
00-63: B channel Trunk Route No.
0 : Provided  
NOTE 1
3 : Not...

CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-PRI Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 69
DESCRIPTION DATA
NOTE 1:This data should be assigned to 
the B channel trunk route.  For 
D channel trunk route, no data 
setting is required.
NOTE 2:This data should be assigned to 
both B channel trunk route and 
D channel trunk route.
(1)
(2)YY=16 
Hooking Signal Sending to outside
00-63: B channel Trunk Route No.
0: Not sending  
NOTE 1

(1)
(2)YY=18 Digit conversion on DID...