NEC Neax 2000 Ivs2 Isdn System Manual

 NEAX2000 IVS2 ISDN System ManualPage 70  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-PRI Programming
 For originating calls to the ISDN, do the following programming:
DESCRIPTION DATA
Assign ISDN access code to each trunk 
route assigned by CM30 YY=00.
NOTE:LCR can be used with ISDN-PRI. 
Refer to Feature Programming 
Manual.
(1)
(2)Y=0-3 Numbering Plan Group 0-3
X-XXXX: Access code
100-163: Trunk Route 00-63
Specify the timing start when making an 
ISDN call from an attendant.(1)...

CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-PRI Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 71
 When providing Tandem Connection (ODT/DTI to ISDN, ISDN to ODT/DTI), do the following
programming:
DESCRIPTION DATA
Specify the combination of trunk routes 
allowing the tandem connection.
(1)
(2)Y=0
XX ZZ
XX: 00-63: Incoming Trunk Route
ZZ : 00-63: Outgoing Trunk Route
0 : Allowed
1: Restricted
Specify the timing start when making an 
ISDN call from a station (PB/DP...

 NEAX2000 IVS2 ISDN System ManualPage 72  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-PRI Programming
 When providing Tandem Connection (ISDN to CCIS, CCIS to ISDN), do the following
programming:
DESCRIPTION DATA
Specify the combination of trunk routes 
allowing the tandem connection.
(1)
(2)Y=0
XX ZZ
XX: 00-63: Incoming Trunk Route
ZZ : 00-63: Outgoing Trunk Route
0 : Allowed
1: Restricted
Allow tandem connection by station or 
attendant.(1)
(2)028
0: Available
CM08
END
CM36
G 

CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-PRI Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 73
D Channel Handler Assignment
DESCRIPTION DATA
When you use the DCH card (PN-SC01), 
assign an AP number to the DCH card.
The AP number must match the SENS 
switch settings on the DCH card.
When you use the PRT card, skip this 
assignment.
(1)
(2)Y=0
04-15, 20-31: AP No.
12: DCH card
Select DCH for ISDN-PRI.
(1)
(2)YY=14
04-15, 20-31: AP No. assigned by 
CM05
0 : PN-24PRTA...

 NEAX2000 IVS2 ISDN System ManualPage 74  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-PRI Programming
DESCRIPTION DATA
Assign the DTI/PRT trunk number 
assigned by CM07 YY=01 to each DCH 
number for providing D channel path 
between DTI/PRT and DCH.
(1)
(2)YY=00 
0-7: DCH No. assigned by CM06
000-255: DTI/PRT Trunk No. assigned 
by CM07 YY=01
CMA9
A
END
DCH INITIAL 

CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-BRI Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 75
ISDN-BRI PROGRAMMING
BRT Assignment
DESCRIPTION DATA
Assign an AP number to the BRT card.
The AP number must match the SENS 
switch setting on the BRT card.
(1)
(2)Y=0
04-15, 20-31: AP No.
10: BRT card 
Assign the ISDN Protocol Type for DCH 
circuit on the BRT card.
(1)
(2)YY=06
04-15, 20-31: AP No. of BRT assigned 
by CM05
ISDN Protocol Type
17 : Australia
18 : New Zealand
20...

 NEAX2000 IVS2 ISDN System ManualPage 76  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-BRI Programming
DESCRIPTION DATA
Assign trunk route to each ISDN trunk 
used for Voice channel (B channel). 
NOTE:BRT route must be separated 
from analog trunk routes. 
(1)
(2)YY=00 
000-255: Trunk No. assigned by CM07 
YY=01 
00-63: Trunk Route
Assign the trunk route data to each ISDN 
incoming trunk used for Voice channel 
only. 
NOTE:If CM35 YYY=143 is set to “1” for 
Event Based CCIS, this...

CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-BRI Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 77
DESCRIPTION DATA

(1)
(2)YY=05 Release signal from distant 
office
00-63: B channel/D channel Trunk 
Route No.
1 : Release signal arrives  
NOTE 2

(1)
(2)YY=09 Incoming Connection Signaling
00-63: Trunk Route No.
08: ISDN Indial

(1)
(2)YY=11 Toll Restriction
00-63: B channel Trunk Route No.
0 : Provided  
NOTE 1
3 : Not provided

(1)
(2)YY=12 
Number of digit to be received...

 NEAX2000 IVS2 ISDN System ManualPage 78  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-BRI Programming
DESCRIPTION DATA
NOTE 1:This data should be assigned to 
the B channel trunk route.  For 
D channel trunk route, no data 
setting is required.
NOTE 2:This data should be assigned to 
both B channel trunk route and 
D channel trunk route.
(1)
(2)YY=19
00-63: B channel Trunk Route No.
0-3 : Programmable PAD 
(See CM42)
4-7 : Fixed PAD
NOTE 1
NOTE:For details of PAD data, refer to...

CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-BRI Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 79
 For originating calls to the ISDN network, do the following programming:
DESCRIPTION DATA
When the data for CM35 YY=18 is set to 
“0” (Received digits conversion is to be 
provided), assign the data for interpreting 
the digits received.



(1)
(2)YY=01 Day Mode
YY=02 Night Mode
YY=03 Mode A
YY=04 Mode B
000-999: Number Conversion Block 
No. assigned by CM76 Y=00...