NEC Neax 2000 Ivs2 Isdn System Manual
Here you can view all the pages of manual NEC Neax 2000 Ivs2 Isdn System Manual. The NEC manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 171
NEAX2000 IVS2 ISDN System ManualPage 160 ND-70919 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION PN-24DTA-C (DTI) (Continued) The figure in the SWITCH NAME column and the position in in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SW1 (Piano Key SW) NOTE 41 Not used 2 Not used 3 Not used 4ON AP...
Page 172
CHAPTER 4 CIRCUIT CARD INFORMATION PN-24DTA-C (DTI) NEAX2000 IVS2 ISDN System Manual ND-70919 (E), Issue 1.0 Page 161 NOTE 1:Set the groove on the switch to the desired position. NOTE 2:When the power is on, flip the MB switch to ON (UP position) before plugging/ unplugging the circuit card. NOTE 3:Set SW0-1 and SW0-2 as follows: NOTE 4:When the PBX is a clock source office, set the SW0-1 and SW0-2 on all the DTI cards mounted in PIM0 to OFF. NOTE 5:Mount the DTI card which receives a source clock...
Page 173
NEAX2000 IVS2 ISDN System ManualPage 162 ND-70919 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION PN-30DTC-A (DTI) PN-30DTC-A (DTI) Locations of Lamps, Switches, and Connectors SENSE RUN MB SW PCM FRM MFRM RMT MRMT AIS BL JP JPSJPR
Page 174
CHAPTER 4 CIRCUIT CARD INFORMATION PN-30DTC-A (DTI) NEAX2000 IVS2 ISDN System Manual ND-70919 (E), Issue 1.0 Page 163 Lamp Indications LAMP NAMECOLOR FUNCTION RUN Green Flashes at 120 IPM when this card is normally operating PCM Red Remains lit when detecting PCM signal loss FRM Red Remains lit when detecting Frame Alignment signal loss MFRM Red Remains lit when detecting Multi-Frame Alignment signal loss on time slot 16 RMT Red Remains lit when receiving the alarm from a distant office because...
Page 175
NEAX2000 IVS2 ISDN System ManualPage 164 ND-70919 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION PN-30DTC-A (DTI) Switch Settings SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SENS (Rotary SW) NOTE 14-F Set the switch to match the AP Number (04-31) to be set by CM05. 0-3 Not used MB (Toggle SW) NOTE 2 UP For make-busy For normal operation (Continued) F 4 AP No.SW-8: ON 04 05 06 07 08 09 10 11 12 13 14 15 SW-8: OFF 20 21 22 23 24 25 26 27 28 29 30 31 SW No. 456789ABCDEF ON DOWN
Page 176
CHAPTER 4 CIRCUIT CARD INFORMATION PN-30DTC-A (DTI) NEAX2000 IVS2 ISDN System Manual ND-70919 (E), Issue 1.0 Page 165 SW (Piano Key SW) 1 NOTE 3 NOTE 4ONSource clock signal from network is sent to the PLO0 input on MP card. OFFSource clock signal from network is not sent to the PLO0 input on MP card 2 NOTE 3 NOTE 4ONSource clock signal from network is sent to the PLO1 input on MP card. OFFSource clock signal from network is not sent to the PLO1 input on MP card. 3ON Remote loop-back For...
Page 177
NEAX2000 IVS2 ISDN System ManualPage 166 ND-70919 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION PN-30DTC-A (DTI) The figure in the SWITCH NAME column and the position in in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. NOTE 1:Set the groove on the switch to the desired position. NOTE 2:When the power is on, flip the MB switch to ON (UP position) before...
Page 178
CHAPTER 4 CIRCUIT CARD INFORMATION PN-30DTC-A (DTI) NEAX2000 IVS2 ISDN System Manual ND-70919 (E), Issue 1.0 Page 167 NOTE 3:Set the SW-1 and SW-2 as follows: NOTE 4:When the PBX is a clock source office, set the SW-1 and SW-2 on all the DTI cards mounted in PIM0 to OFF. NOTE 5:Mount the DTI card which receives a source clock signal into PIM0. CONDITIONSDTI0 DTI1 DTI2 DTI3 REMARKS SW -1SW -2SW -1SW -2SW -1SW -2SW -1SW -2 When one DTI is provided.ON OFF – – – – – –MP card will receive the clock...
Page 179
NEAX2000 IVS2 ISDN System ManualPage 168 ND-70919 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION PN-24PRTA (PRT) PN-24PRTA (PRT) Locations of Lamps, Switches, and Connectors SENSE RUN MB SW2 LC LPB CRC PCM FRM RMT AIS BL SW1 SW0 JRR1 AISS MAS JPR0 JPS
Page 180
CHAPTER 4 CIRCUIT CARD INFORMATION PN-24PRTA (PRT) NEAX2000 IVS2 ISDN System Manual ND-70919 (E), Issue 1.0 Page 169 Lamp Indications Switch Settings LAMP NAMECOLOR FUNCTION RUN Green Flashes at 120 IPM while this card is operating normally LC Green Remains lit when communications are normally ongoing with the D channel data links connected LPB – Not used CRC Red Remains lit when detecting Cyclic Redundancy Checking (CRC) errors PCM Red Remains lit when detecting PCM signal loss FRM Red Remains...