NEC Neax 2000 Ivs2 Ccis System Manual

 NEAX2000 IVS2 CCIS System ManualPage 128  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Forwarding-All Calls-CCIS
Operating Procedure
Single Line Telephone
To set Call Forwarding-All Calls-CCIS from a Single Line Telephone:
(1) Lift the handset; receive dial tone.
(2) Dial the Call Forwarding-All Calls-CCIS access code; receive feature dial tone.
(3) Dial the outgoing trunk access code; receive a single burst of service set tone.
(4) Dial the station number to which calls are to be...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Forwarding-All Calls-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 129
Dterm
To set Call Forwarding-All Calls-CCIS from a My Line:
(1) Lift handset or press SPEAKER key; receive dial tone.
(2) Press the Call Forwarding-All Calls-CCIS feature access key; receive feature dial tone.
(3) Dial the outgoing trunk access code; receive a single burst of service set tone.
(4) Dial the desired station number to which calls are to be forwarded.
(5)...

 NEAX2000 IVS2 CCIS System ManualPage 130  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Forwarding-Busy Line-CCIS
CALL FORWARDING-BUSY LINE-CCIS
General Description
This service feature provides inter-office Call Forwarding-Busy Line-CCIS, which permits a call
to a busy station to be immediately forwarded to a predesignated station or to an Attendant
Console in another office in the CCIS network.
Programming
DESCRIPTION DATA
Assign Service Restriction Class A to the 
required stations....

CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Forwarding-Busy Line-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 131
DESCRIPTION DATA
Specify the Call Forwarding-Busy Line-
Outside setting operation.(1)
(2)222
0 : The feature is set when the station 
goes on hook/when receiving Ser-
vice Set Tone (ORT time out)
1 : The feature is set when receiving 
Service Set Tone (ORT time out)
Allow or restrict the ability to set Call For-
warding-Busy Line for a station with Do 
Not Disturb...

 NEAX2000 IVS2 CCIS System ManualPage 132  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Forwarding-Busy Line-CCIS
When a call is forwarded through CCIS by Call Forwarding-All Calls/-Busy Line/-Don’t Answer,
the kind of Call Forwarding and the station number which is setting the service can be indicated
on the LCD of the forwarding destination D
term.
To provide this feature, perform the following programming.
On the Forwarding side PBX (PBX-A)
On the Forwarded destination side PBX...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Forwarding-Busy Line-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 133
Operating Procedure
Single Line Telephone
To set Call Forwarding-Busy Line-CCIS from a Single Line Telephone:
(1) Lift the handset; receive dial tone.
(2) Dial the specific Call Forwarding-Busy Line-CCIS access code; receive feature dial tone.
(3) Dial the outgoing trunk access code; receive a single burst of service set tone.
(4) Dial the station number to which calls...

 NEAX2000 IVS2 CCIS System ManualPage 134  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Forwarding-Busy Line-CCIS
Dterm
To set Call Forwarding-Busy Line-CCIS from a Dterm:
(1) Lift handset or press SPEAKER key; receive dial tone.
(2) Press the Call Forwarding-Busy Line-CCIS feature access key; receive feature dial tone.
(3) Dial the outgoing trunk access code; receive a single burst service set tone.
(4) Dial the station number to which calls are to be forwarded.
(5) Wait approximately...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Forwarding-Don’t Answer-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 135
CALL FORWARDING-DON’T ANSWER-CCIS
General Description
This service feature provides interoffice Call Forwarding-Don’t Answer-CCIS, which permits a
call to an unanswered station to be forwarded to a pre-designated station or to an Attendant
Console in another office, when the called station does not answer after a predetermined time
interval.
Programming
DESCRIPTION...

 NEAX2000 IVS2 CCIS System ManualPage 136  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Forwarding-Don’t Answer-CCIS
DESCRIPTION DATA
To apply this feature to incoming calls, set 
the trunk route combinations for Tandem 
connection.
(1)
(2)YY=05
00-63: Trunk Route No.
1 : Release Signal arrive
Specify the combination of Trunk Routes 
allowing a Trunk to Trunk (CCIS) 
Connection.
(1)
(2)Y=0
XX ZZ
XX: 00-63 (Incoming Trunk Route)
ZZ: 00-63 (Outgoing Trunk Route)
0: Allow
Specify the...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Call Forwarding-Don’t Answer-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 137
DESCRIPTION DATA
Specify the timing for Call Forwarding-
Don’t Answer for a trunk incoming call.
(1)
(2)Y=0
01
01-30: 0-120 sec. (4 sec. increments)
If no data is set, the default setting is 32-36 
seconds.
Specify the timing for Call Forwarding-
Don’t Answer for an internal call or an 
assigned call.
(1)
(2)Y=0
15
01-30: 4-120 sec. (4 sec. increments)
If no data...