NEC Neax 2000 Ivs2 Ccis System Manual

 NEAX2000 IVS2 CCIS System ManualPage 78  ND-70918 (E), Issue 1.0
CHAPTER 2  INSTALLATION
Installation Procedure
 When providing the Common Signaling Data Link via LDT/ODT:
(1) Connect the RS NORM-4 CA-A/RS NORM-4S CA-A to the CCH card and the MODEM 
(PBX side) as shown in Figure 2-14.
Figure 2-14  Cabling of RS NORM-4 CA-A/RS NORM-4S CA-A
(for Common Signalling Data Link via LDT/ODT)
(2) Connect the LINE cable to the MODEM and the MDF.
Figure 2-15 shows LTC connector with corresponding AP slots and CCH...

CHAPTER 2  INSTALLATION
Installation Procedure
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 79
Figure 2-15  Location of the AP Slots and the LTC Connectors for CCH
LT C 0LT C 1LT C 2LT C 3
VM LT00/AP00 LT01/AP01 LT02/AP02 LT03/AP03
LT04/AP04 LT05/AP05 LT06/AP06 LT07/AP07 LT08/AP08 LT09/AP09 LT10/AP10 LT11/AP11/FP11 MP12/FP12 PFT
LT00/AP00
LT01/AP01
LT02/AP02
26 TXT
27 RCVT
TXT
RCVT
TXT
RCVT 28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50 TXR
RCVR
TXR
RCVR
TXR...

 NEAX2000 IVS2 CCIS System ManualPage 80  ND-70918 (E), Issue 1.0
CHAPTER 2  INSTALLATION
Installation Procedure
Figure 2-16 shows an example of the cable connection when the CCH card is mounted in the
AP05 slot of PIM0.
Figure 2-16  Cabling of LINE Cable (for Common Signalling Data Link via LDT/ODT)
42 TXT 17 TXR
43 RCV T 18 RCV R
44 19
45 2017 TXR 42 TXT
18 RCV R 43 RCV T
19 44
20 45
PIM 0
JPMDF
CCH
AP05 
[LT05] LT C 1
MODULAR
19
44
20
45
44
20
45 19
TX R
TX T
RCV R
RCV T17
42
18
43 42
18
43 17...

NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 81
CHAPTER 3
SYSTEM DATA 
PROGRAMMING
This chapter explains the programming procedure for providing CCIS
system, and also explains the general description, programming
procedure, operating procedure, and hardware requirement of each
service feature. 

 NEAX2000 IVS2 CCIS System ManualPage 82  ND-70918 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
How To Read This Chapter
HOW TO READ THIS CHAPTER
This chapter explains the feature programming for each service feature about the following
Abbreviations.
(1) : 1st data
(2) : 2nd data
: Initial data; With the system data clear command (CM00, CM01), the data with this
marking is automatically set for each command.
: A reset of the MP card is required after data setting.
Press SW1 switch on the MP card.
:...

CHAPTER 3  SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 83
NO. 7 CCIS WITH DIGITAL INTERFACE
Perform the programming according to the procedures shown in Figure 3-1.
Figure 3-1  Programming Procedure (for No. 7 CCIS with Digital Interface)
 Page 115
END
INTER-TENANT CONNECTION
ASSIGNMENT NUMBERING PLAN
ASSIGNMENT DTI ASSIGNMENT
CCH ASSIGNMENT
START
 Page 95
 Page 91
 Page 89
 Page 84
NO. 7 CCIS FEATURE
PROGRAMMING 

 NEAX2000 IVS2 CCIS System ManualPage 84  ND-70918 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
DTI Assignment
DESCRIPTION DATA
Assign an AP number to each DTI card. 
The AP number must match the switch 
settings on the DTI card.•
(1)
(2)Y=0
04-15, 20-31: AP No.
09: DTI card
Specify the AP highway channel for 24-
DTI card.
NOTE:This command is only applicable 
for the 24 DTA-C card.
(1)
(2)Y=1
04-15, 20-31: AP No.
0 : Expanded Highway channel
(128 time slots)
1 :...

CHAPTER 3  SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 85
DESCRIPTION DATA
Assign the necessary functions to each 
DTI (24-DTI) cards.
After entering the data, set the MB switch 
on the DTI card to UP, and then to DOWN, 
for DTI initialization.
NOTE 1:This command is only applicable 
for the 24-DTI card.
NOTE 2:The following table shows the 
relationship between CMAA 
YY=01 and YY=02.
[ ] indicates 2nd Data
NOTE 3:If 56K...

 NEAX2000 IVS2 CCIS System ManualPage 86  ND-70918 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
DESCRIPTION DATA
Assign the trunk route data for common 
signaling channel and voice channels.
Minimum of two routes.
(1)
(2)YY=00
00-63: Trunk Route No.
04: Tie Line

(1)
(2)YY=01
00-63: Trunk Route No.
7 : DP/DTMF

(1)
(2)YY=04
00-63: Trunk Route No.
2: Answer Signal arrives

(1)
(2)YY=05
00-63: Trunk Route No.
1 : Release Signal arrives 
Specify the incoming...

CHAPTER 3  SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 87
DESCRIPTION DATA
For Australia:For North America/Other Countries:
When using the programmable PAD 
(CM35 YY=19, 2nd Data=0-3), assign the 
PAD data.(1)
(2)50-65: See tables below.
00-15: See tables below.
CM42
C
D
CM35
T/R: Transmit/Receive
+: Gain
–: Loss
CONNECTION
PATTERNS (A-B)PAD DATA OF B TRUNK [dB]
DATA
=4 
(T/R)DATA
=5 
(T/R)DATA
=6 
(T/R)DATA
=7 
(T/R)...