NEC Neax 2000 Ivs2 Ccis System Manual

 NEAX2000 IVS2 CCIS System ManualPage 108  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
NO. 7 CCIS WITH ANALOG INTERFACE
Do the programming according to the procedures shown in Figure 3-2.
Figure 3-2  Programming Procedure (for No. 7 CCIS with Analog Interface)
END
INTER-TENANT CONNECTIONNUMBERING PLAN
ASSIGNMENT LDT/ODT ASSIGNMENT
CCH ASSIGNMENT
No. 7 CCIS FEATURE
START
 Page 109
 Page 114
 Page 114
 Page 114
 Page 115PROGRAMMINGASSIGNMENT 

CHAPTER 3 SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 109
LDT/ODT Assignment
DESCRIPTION DATA
Assign a trunk number to each LDT/ODT.
NOTE:The Trunk number must be 
assigned to the 1st LEN (Level 0) 
and 2nd LEN (Level 1) of each 
LT slot.(1)
(2)000-763: LEN
D000-D255: Trunk No.
Assign a trunk route number to each trunk.
(1)
(2)YY=00
000-255: Trunk No. assigned by CM10
00-63: Trunk Route No.
Assign the trunk route data for...

 NEAX2000 IVS2 CCIS System ManualPage 110  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
DESCRIPTION DATA
Specify the PAD Patterns on the voice 
channel route.
For Australia:
(1)
(2)YY=19
00-63: Trunk Route No.
0-3 : Programmable PAD 
(See CM42 on Page 112.)
4-7 : Fixed PAD 
(See left column.)
CM35
A
B
T/R: Transmit/Receive
+: Gain
–: LossCONNECTION
PATTERNS (A-B)PAD DATA OF B TRUNK [dB]
DATA
=4 (T/R)DATA
=5 (T/R)DATA
=6 (T/R)DATA
=7 (T/R)
Station-ODT0/0...

CHAPTER 3 SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 111
DESCRIPTION DATA
For North America/Other Countries:
Provide the voice channel route with No. 7 
CCIS facilities.
(1)
(2)YY=90
00-63: Trunk Route No.
0: No. 7 CCIS
Assign a CCIS channel number to each 
voice channel route.
(1)
(2)YY=91
00-63: Trunk Route No.
0-7: CCIS channel No.
Assign a Circuit Identification Code (CIC) 
number to each trunk number used for...

 NEAX2000 IVS2 CCIS System ManualPage 112  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
DESCRIPTION DATA
When using the programmable PAD 
(CM35 YY=19, 2nd Data=0-3), assign the 
PAD data.(1)
(2)50-65: See tables below.
00-15: See tables below.C
CM42
For Australia:
T/R: Transmit/Receive
+: Gain
–: LossPAD DATA PATTERNS
CONNECTING
PATTERNS (A-B) CM35 YY=19
2ND DATA=0CM35 YY=19
2ND DATA=1CM35 YY=19
2ND DATA=2CM35 YY=19
2ND DATA=3
50
6550 54 58 62...

CHAPTER 3 SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 113
DESCRIPTION DATA
For North America/Other Countries:
END
CM42
D
T/R: Transmit/Receive
+: Gain
–: LossPATTERNS
2ND DATAPAD DATA OF B TRUNK (T/R) [dB]
ODT (4W E&M) ODT (2W E&M) COT/DID/LDT
00
1500 0/0 0/0 0/0
01 0/0 0/0 0/0
02 0/0 0/0 0/0
03 –2/–2 –3/–3 –3/–3
04 –3/–3 0/0 0/0
05 –12/–11 –6/–6 –6/–6
06 –16/–11 0/0 0/+5
07 –6/–6 0/0 +3/+3
08
15Not Used
~
~ 

 NEAX2000 IVS2 CCIS System ManualPage 114  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
CCH Assignment
Perform the same programming procedure for CCH Assignment as shown in CCH Assignment
on Page 89). Note that the assignment of trunk number by CMA7 YY=00 is not required when
the CCH is connected with a dedicated line. CMA7 YY=00 is required when the common
signaling channel is connected via an LDT/ODT card.
Numbering Plan Assignment
Perform the same...

CHAPTER 3 SYSTEM DATA PROGRAMMING
No. 7 CCIS Feature Programming
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 115
NO. 7 CCIS FEATURE PROGRAMMING
This section explains the feature programming of No. 7 CCIS services required for a particular
data assignment.
The following features require no programming. Additional information on these features may be
found in the Features and Specifications.
 Elapsed Time Display-CCIS
 Hands-Free Answer Back-CCIS
 Individual Attendant...

 NEAX2000 IVS2 CCIS System ManualPage 116  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Attendant Camp-on With Tone Indication-CCIS
ATTENDANT CAMP-ON WITH TONE INDICATION-CCIS
General Description
This feature provides inter-office Attendant Camp-On service which permits the operator, when
the desired station at another switching office is busy, to hold an incoming call in a special waiting
mode. A distinctive Camp-On Tone Indication is sent to the busy station when the operator sets
Camp-On....

CHAPTER 3 SYSTEM DATA PROGRAMMING
Attendant Camp-on With Tone Indication-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 117
To reenter a Camped-On trunk from an Attendant before Automatic Recall:
To display the busy station number and name on an Attendant Console when reentering a
Camped-On trunk by pressing the loop key:
Operating Procedure
To activate an Attendant Camp-On with Tone Indication-CCIS from the Attendant Console:
(1) Dial the desired station number at another...