NEC Neax 2000 Ivs2 Ccis System Manual

 NEAX2000 IVS2 CCIS System ManualPage 98  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
Example of No. 7 CCIS with Digital Interface
(1) For open numbering system
CCH
CIC=1
CIC=2
TRK000
TRK001
TRK002CIC=2
RT1131xx
CCH0
CIC=1
CCIS CH0RT10
32xx
TRK003
TRK004
TRK005CIC=2
RT13
CCH1
CIC=1
CCIS CH1RT12 21xx
CCH
CIC=1
CIC=2
34xx35xx OFFICE CPC: 00020
OFFICE NO.: 825 DTI1 DTI0 OFFICE A PC: 00001
OFFICE NO.: 820OFFICE B PC: 00010
OFFICE NO.: 822
CONDITIONS:
 Open...

CHAPTER 3 SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 99
For office A, the following programming is required:
(1) Assign the DTI card.
(2) Assign a trunk number to the required DTI channels.
(3) Assign DTI card parameters.
(These data assignments are only for 24-DTI card.)
(4) Assign a trunk route number to the DTI trunks.
Command Code 1st Data 2nd Data
05 Y=0 04 09 : DTI0
05 09 : DTI1
05 Y=1 04 1 : Basic Highway channel
05...

 NEAX2000 IVS2 CCIS System ManualPage 100  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
(5) Assign trunk route data
(6) Assign CCH card
Command Code 1st Data 2nd Data
35 YY=00 10 04
Tie Line Route Assignment 11 04
12 04
13 04
35 YY=01 10 7
Dialing Signal Type 11 7
12 7
13 7
35 YY=04 10 2
Answer Signal 11 2
12 2
13 2
35 YY=05 10 1
Release Signal 11 1
12 1
13 1
35 YY=09 10 03
Incoming Connection Signal 11 03
12 03
13 03
35 YY=19 10 0-7
DTI Pad Pattern...

CHAPTER 3 SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 101
(7) Assign CCIS channel number to each CCH
(8) Provide the system with No. 7 CCIS
(9) Assign CCIS channel number to each route
(10) Assign a CIC number to each voice channel trunk.
(11) Assign CCIS channel data.
Command Code 1st Data 2nd Data
06 YY=07 0 06 : CCIS Channel 0
1 07 : CCIS Channel 1
Command Code 1st Data 2nd Data
09 53 0
Command Code 1st Data 2nd Data
35...

 NEAX2000 IVS2 CCIS System ManualPage 102  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
(12) Assign route access data.
NOTE:This example shows 
Second Dial tone will be heard only after 8 is dialed.
8 will be added and sent to Distant PBX.
Command Code 1st Data 2nd Data
20 Y=0 8 A126 : Access Code=8
8A YYYY=A000 0 4005 : Area Code Development Pattern No. 5
8A YYYY=4005 22 0000 : Route Pattern 0000
25 0001 : Route Pattern 0001
8A YYYY=0000 1 00010 : Trunk...

CHAPTER 3 SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 103
(2) For closed numbering system
EXAMPLE
OFFICE A PC: 00001 
OFFICE NO.: 21
21xxOFFICE B PC: 00010 
OFFICE NO.: 22
DTI0
TRK000
TRK001
TRK002
CCH0
DTI1
TRK003
TRK004
TRK005
CCH1CIC=1
CIC=2
CCIS CH0
CIC=1
CIC=2
CCIS CH1RT10
RT11
RT12
RT13CIC=1
CIC=2
CCH
CIC=1
CIC=2
CCH22xx
OFFICE C
25xx PC: 00020 
OFFICE NO .: 25
CONDITIONS:
  Closed Numbering (4-digit Station number)...

 NEAX2000 IVS2 CCIS System ManualPage 104  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
For office A, the following programming is required:
(1) Assign the DTI card.
(2) Assign a trunk number to the required DTI channels.
(3) Assign DTI card parameters.
(These data assignments are only for 24-DTI card.)
(4) Assign a trunk route number to the DTI trunks.
Command Code 1st Data 2nd Data
05 Y=0 04 09 : DTI0
05 09 : DTI1
05 Y=1 04 1 : Basic Highway channel
05 1 :...

CHAPTER 3 SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 105
(5) Assign trunk route data.
(6) Assign CCH card.
Command Code 1st Data 2nd Data
35 YY=00 10 04
Tie Line Route Assignment 11 04
12 04
13 04
35 YY=01 10 7
Dialing Signal Type 11 7
12 7
13 7
35 YY=04 10 2
Answer Signal 11 2
12 2
13 2
35 YY=05 10 1
Release Signal 11 1
12 1
13 1
35 YY=09 10 03
Incoming Connection Signal 11 03
12 03
13 03
35 YY=19 10 0-7
DTI Pad Pattern...

 NEAX2000 IVS2 CCIS System ManualPage 106  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
(7) Assign CCIS channel number to each CCH.
(8) Provide the system with No. 7 CCIS.
(9) Assign CCIS channel number to each route.
(10) Assign a CIC number to each voice channel trunk.
(11) Assign CCIS channel data.
Command Code 1st Data 2nd Data
06 YY=07 0 06 : CCIS Channel 0
1 07 : CCIS Channel 1
Command Code 1st Data 2nd Data
35 YY=09 53 0
Command Code 1st Data 2nd...

CHAPTER 3 SYSTEM DATA PROGRAMMING
No. 7 CCIS With Digital Interface
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 107
(12) Assign route access data.
NOTE:This example shows   
No second dial tone will be heard.
No digits will be added.
Command Code 1st Data 2nd Data
20 Y=0 22 A129 : Access Code=22
20 Y=0 25 A129 : Access Code=25
8A YYYY=A000 3 4007 : Area Code Development Pattern No. 5
8A YYYY=4007 22 0000 : Route Pattern 000 (22XX)
25 0001 : Route Pattern 001 (25XX)
8A YYYY=0000 1...