NEC Neax 2000 Ivs2 Ccis System Manual

 NEAX2000 IVS2 CCIS System ManualPage 68  ND-70918 (E), Issue 1.0
CHAPTER 2  INSTALLATION
Installation Procedure
Figure 2-5 shows LTC connectors with corresponding AP slots and DTI pin assignment for each
AP slot.
Figure 2-5  Location of the AP Slots and the LTC Connectors for DTI
LT C 0LT C 1LT C 2LT C 3
VM LT00/AP00 LT01/AP01 LT02/AP02 LT03/AP03 LT04/AP04 LT05/AP05 LT06/AP06 LT07/AP07 LT08/AP08 LT09/AP09 LT10/AP10 LT11/AP11/FP11 MP12/FP12 PFT
LT00/AP00
LT01/AP01
LT02/AP02
26 RB
27 TB
28
29
30
31
32
33...

CHAPTER 2  INSTALLATION
Installation Procedure
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 69
Figure 2-6 shows an example of the cable connection when the DTI card is mounted in the AP05
slot of PIM0.
Figure 2-6  Example of Cable Connection via MDF
17 
18 
19 
20RA 
TA42 
43 
44 
45RB 
TB LT C 1  ( J )42 
43 
44 
45RB 
TB17 
18 
19 
20RA 
TA LT C 1  ( P ) PIM 0
JP MDF DTI
AP05
RA
RB
TA
TB17
42
18
4317
42
18
43RA
RB
TA
TBTO CS U LT C 1
RECEIVE
TRANSFER 

 NEAX2000 IVS2 CCIS System ManualPage 70  ND-70918 (E), Issue 1.0
CHAPTER 2  INSTALLATION
Installation Procedure
Cable Connection via CONN Card
When using a coaxial cable, connect the cable to a CSU via the CONN (PZ-M542/PZ-M557) card
as shown in Figure 2-7.
Figure 2-7  DTI Cable Connection via CONN Card
CSU
LTC0/LTC1/LTC2/LTC3 CONNECTORCOAXIAL CABLE 30-DTI BWBPBX
MAX. 6 dB loss at 1024 kHz
CONN (PZ-M542/PZ-M557) 

CHAPTER 2  INSTALLATION
Installation Procedure
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 71
Figure 2-8 shows an example of the cable connection when the 30-DTI card is mounted in the
AP05 slot of PIM0.
Figure 2-8  Example of Cable Connection via the CONN Card
COAXIAL CONNECTOR LTC1 CONNECTOR
17 
18 
19 
20RA 
TA42 
43 
44 
45RB 
TB LT C 1  ( J )42 
43 
44 
45RB 
TB17 
18 
19 
20RA 
TA LT C 1  ( P )
12
PIM 0
JPCONN CARD
DTI
AP05
RA
RB
TA
TB17
42
18
4317
42
18
43TO  C SU
LT C 1...

 NEAX2000 IVS2 CCIS System ManualPage 72  ND-70918 (E), Issue 1.0
CHAPTER 2  INSTALLATION
Installation Procedure
Optical Cable Connection
When you use an optical cable for DTI, connect the cable each other to the CN1 connector of the
M10 (PN-M10) cards.
M10 card and DTI cards are connected via MDF through LTC connector on the BWB.
Figure 2-9 and Figure 2-10 show the outline of connection and example of M10 MDF cross
connection.
Figure 2-9  Outline of Optical Cable Connection
MDF
OPTICAL 
CABLE
CN1
MAX....

CHAPTER 2  INSTALLATION
Installation Procedure
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 73
Figure 2-10  Example of MDF Cross Connection for M10 Card (1 of 2)
PIM 0
JP MDF DTI
AP09 
[LT09]
RA 1 1 RA
RB 26 26 RB
TA 2 2 TA
TB 27 27 TB
LT C 3
RECEIVE
TRANSFER
1
JP DTI
AP10 
[LT10]
RA 9 9 RA
RB 34 34 RB
TA 10 10 TA
TB 35 35 TB
LT C 3
RECEIVE
TRANSFER
2
JP M10
No. 1
AP05 
[LT05]
RA 19 19 RA
RB 44 44 RB
TA 20 20 TA
TB 45 45 TB
LT C 1
TO OPPOSITE M10 CARD CN1RECEIVE
TRANSFER
3
RA 17 17...

 NEAX2000 IVS2 CCIS System ManualPage 74  ND-70918 (E), Issue 1.0
CHAPTER 2  INSTALLATION
Installation Procedure
Figure 2-10  Example of MDF Cross Connection for M10 Card (2 of 2)
1 
2 
3 
4RA 
TA26 
27 
28 
29RB 
TB
LT C  ( J )26 
27 
28 
29RB 
TB1 
2 
3 
4RA 
TA
(P) 1  LTC3 CONNECTOR
9 
10 
11 
12RA 
TA34 
35 
36 
37RB 
TB
LT C  ( J )34 
35 
36 
37RB 
TB9 
10 
11 
12RA 
TA
(P) 2  LTC3 CONNECTOR
17 
18 
19 
20RA 
TA42 
43 
44 
45RB 
TB
LT C  ( J )42 
43 
44 
45RB 
TB17 
18 
19 
20RA 
TA
(P) 3  LTC1...

CHAPTER 2  INSTALLATION
Installation Procedure
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 75
No. 7 CCIS with Analog Interface
Perform necessary installation works of the equipment according to the procedure shown in
Figure 2-11.
Figure 2-11  Installation Procedure for No. 7 CCIS with Analog Interface
START
MOUNTING CCH CARD
MOUNTING EXPMEM CARD
MOUNTING LDT/ODT CARD
MOUNTING AP00 CARD
 Page 61
 Page 76
 Page 62
 Page 63
END
CABLE CONNECTION
AT CCH AND MODEMThis procedure is...

 NEAX2000 IVS2 CCIS System ManualPage 76  ND-70918 (E), Issue 1.0
CHAPTER 2  INSTALLATION
Installation Procedure
Mounting LDT/ODT Card
Mount the LDT (PN-2LDTA) and ODT (PN-2ODTA/PN-2ODTB) cards in LT
slots.
AT T E N T I O NContents
Static Sensitive
Handling
Precautions Required 

CHAPTER 2  INSTALLATION
Installation Procedure
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 77
Cable Connection at CCH and MODEM
 When providing the Common Signaling Data Link via MODEM:
(1) Connect the RS NORM-4 CA-A/RS NORM-4S CA-A to the CCH card and the MODEM 
(PBX side) as shown in Figure 2-12.
Figure 2-12  Cabling of RS NORM-4 CA-A/RS NORM-4S CA-A 
(for Common Signaling Data Link via MODEM)
(2) Connect the LINE cable between the MODEM (PBX side) and MODEM (Distant PBX side)...