Mitel Voice Processing Solutions Installation And Service Manual

cp 6282Disk Addition (add.disk)Page 1 of 5
VoiceMemo Release 6.OA and later
This procedure describes how to increase the storage capacity by adding a primary disk
to a Centigram Series 6 server.This procedure can be performed while the server is
online.For instructions describing how to add storage redundancy to a server by adding
a single redundant disk, see CP 628 1 Redundant Disk Addition (make.redundant).
FOR THE MODEL 70 ONLY:Some system prompts in this procedure may contain
generic references to...

CP 6282
Page 2 of 5VoiceMemo Release 6.OA and later
step
CD Prepare the New Disk
1.Determine how to jumper the new hard disk as an IDE “slave” disk.
2.Jumper the new hard disk. If there are two hard disks in one server, one must be
configured as master and the other must be configured as slave.If there is one hard
disk in the server, it must be configured as master.IDE hard disks are shipped from
Centigram configured as master.
. .
@9 Prepare the System
3.Reach the Hard Disk Utilities Menu, then go to...

Cl? 6282
Page 3 of 5VoiceMemo Release 6.OA and later
Step
@D Run the Add Disk Program From the Hardware
Configuration Menu
IO. Turn on the power to the system, and boot from the hard disk.
11. Reach the 
VoiceMemo Hardware Configuration Menu, then to go the Disk
Configuration Menu.
12. Add the disk.
Select:(A) Add a single disk
Prompt: Please insert service diskette
drive, hit  when readyResponse: Insert the Service Diskette, and press Enter.
I
into floppy
Prompt: Specify one of the following bus:diskId...

 rCP 6282
Page 4 of 5VoiceMemo Release 6.OA and later
Step
17. The server reads from the diskette, then requests the service diskette.
Pr0mpt: Insert floppySERVICE 6.00 and hit return
Response: Insert the diskette, and press Enter.18. The server reads from the diskette, and asks which process you want to execute.
prompt: Enter one of the names:
Response: add&k19. The server reads from the diskette, and issues a warning about the pending process.
Prompt:*****WARNING:
ADD-DISK PROGRAM*******
ADD.DISK...

Cl? 6282
Page 5 of 5
VoiceMemo Release 6.OA and later
stebRefireme20. Add the active (or primary) disk.
Prompt: Which disk do you want to add?
Enter the disk id (path:target), 
 to stop,
or ? for help:
SpeechAccounts
Software
Prompts(Messages)(Mailboxes etc.)
-------- ------- 
------====-------- -------=================Configuration 1:YesYesXX Hours
xxxx Account Records
Configuration 2: NoNOXX HoursXXXX Account Records-__-----_-__--_____-____________________--~~-----~~~~~~----s.----Please select the...

I
Online Disk Replacement (RedundantSystems)
cp 6283Page 1 of 2
VoiceMemo Release 6.OA and later
This procedure describes how to replace a hard disk for a single or multi-module server
with 
fir11 disk redundancy. This procedure can be performed while the server is online.
FOR THE MODEL 70 ONLY: Some system prompts in this procedure may contain
generic references to other multiple-module Centigram Series 6 products. In such cases,
shaded areas indicate a difference in operations for the Model 70. The...

CP 6283
Page 2 of 2VoiceMemo Release 6.OA and later
steb
5.If any disk, other than the disk to be replaced, is out of sync with its redundantmate, update the redundancy. Do not update the redundancy of the disk to be
replaced.
6.Shut down the system.Leave the status of all modules enabled.
I7.Turn off the system power.
8.Change the hardware, removing the disk to be replaced.
9.Install the new hard disk and replace the cabinet cover.
10. Turn on the system power.11. Reach the 
VoiceMemo Hardware...

Offline Disk Replacement
(Non-Redundant/Redundant Systems)CP 6592Page 1 of 4
VoiceMemo Release 6.OA and later
This procedure describes how to replace a defective or malfunctioning hard disk with a
new hard disk in a non-redundant or redundant Centigram Series 6 server. This
procedure must be performed while the server is offline. (Although this procedure can be
used for redundant systems, Centigram recommends CP 6283, Online Disk
Replacement (Redundant Systems) for redundant disk replacement.)
This...

06592Page 2 of 4
VoiceMemo Release 6.OA and later
Step
3.Run an Online System Verify.
4.Perform a floppy backup.
5.Shut down the system.
6.Turn off the system power.
CC9 Set Up the Hardware7. Remove cabinet cover.
L.8.Disconnect the disk cable from the existing hard disk and remove it from the
cabinet.
9.Rejumper the existing (defective or malfunctioning) hard disk from master to slave.
10. Reconnect the disk cable to slave hard disk. Do not reinstall the hard disk.
11. Jumper the new hard disk to...

CP 6592
Page 3 of 4VoiceMemo Release 6.OA and later
Step20. Insert the Service Diskette and press Enter. From the menu of options, select
REPLACE.DISK.
2 1. The server displays a warning message. This is your prompt to verify that both harddisks are correctly connected and that you did a floppy backup before you started
this procedure. If you failed to complete these requirements, stop the procedure at
this point and complete them.
prompt: WARNING! !******* REPLACE PROGRAM*******
REPLACE programshould...