Home > Mitel > Communications System > Mitel Voice Processing Solutions Installation And Service Manual

Mitel Voice Processing Solutions Installation And Service Manual

Here you can view all the pages of manual Mitel Voice Processing Solutions Installation And Service Manual. The Mitel manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 101

Cl? 6220
Page 3 of 4
VoiceMemo Release 6.OA and later
StepFigure 2 Slot CoverReferenceFigure 1
Remove the 
Line Card
Dot. REV. A 

Page 102

CP 6220Page 4 of 4
VoiceMemo Release G.OA and later
SreDReference
@SD Install the line Card
6.Verify that you have the correct kind of line card for this server.
7.If you are expanding the server and installing a line card into a previously unused
slot, remove the slot cover.
a.Insert the tip of a small flat-bladed screwdriver in the slot at the lower inside end
of the slot cover.
b.Slightly twist the screwdriver, popping up the slot cover. From inside the 
8.cabinet, lift the slot up and out.
A...

Page 103

This procedure first describes how to remove and then how to install the hard disk in the
Centigram Series 6 Model TO. It also describes how to remove and reinstall the disk
carrier. The drive carrier houses both the hard disk and the floppy disk drive.
DANGER!Disconnect the system from its power source before connecting
cables, components, or both.
CAUTION!Protect your system from ESD damage during handling of all
components.
*,
Note:You can find TRs referenced in this procedure in the Centigram Series...

Page 104

Cl’ 6221
Page 2 of 5
VoiceMemo Release 6.OA and later
SteDReference
QE9 Remove the Disk Carrier
WARNING!When the disk carrier is removed from the system, the power
switch terminals are accessible. These terminals can have
hazardous voltages present even when the power switch is turned
off. Unplug the system before performing the procedure. Failure
to do so can result in personal injury and/or equipment damage.
6. Remove cabinet cover.
7.Disconnect the data and power cables from both the hard disk and the...

Page 105

Cl? 6221
Page 3 of 5
VoiceMemo Release 6.OA and later
Step
3-l/2” Drive Carrier
Figure 1Remove the Hard Disk
@Zl Remove the Hard Disk10. Remove all screws securing the hard disk to the carrier (there are usually three or
four).Do not remove the EM1 shield and the filter panel at the front of the bay.
e11. Remove the hard disk from the carrier. See Figure 2 for details.
12. If required, transfer data from the old disk to the new disk.
13. Place the hard disk on an anti-static wrapper.
Note:If you are...

Page 106

VoiceMemo Release G.OA and later
Figure 2Remove the Hard Disk
@GB Install the Hard Disk and Disk Carrier
Note:If you are performing fault isolation and installing the hard disk into a
spare cabinet, remove the disk carrier as previously described.
6.Configure the hard disk, if required. If there are two hard disks in one server, one
must be configured as master and the other must be configured as slave. If there is
one hard disk in the server, it must be configured as master.
Hard disks are shippedfrom...

Page 107

CP 6221
Page 5 of 5VoiceMemo Release 6.OA and later
stepReference
12. Lower the carrier into the cabinet, lining up the front tab on the carrier with the slot
that projects from the side of the 
5.25inch bay.
13. Slide the carrier toward the front until the left front tab and the screw holes line up.
14. Secure the carrier into the cabinet using four mounting screws (6-32 hex head
Phillips screws).
Note:If the floppy disk drive needs to be properly aligned with the front
bezel, loosen the mounting screws...

Page 108

CT? 6221Page 4 of 5
VoiceMemo Release 6.OA and later
StepReference
Figure 2Remove the Hard Disk
@3J Install the Hard Disk and Disk Carrier
Note:If you are performing fault isolation and installing the hard disk into a
spare cabinet, remove the disk carrier as previously described.
6.Configure the hard disk, if required. If there are two hard disks in one server, one
must be configured as master and the other must be configured as slave. If there is
one hard disk in the server, it must be configured as...

Page 109

Cl? 6221
Page 5 of 5
VoiceMemo Release 6.OA and later
SteD
12. Lower the carrier into the cabinet, lining up the front tab on the carrier with the slot
that projects from the side of the 
5.25-inch bay.
13. Slide the carrier toward the front until the 
left front tab and the screw holes line up.
14. Secure the carrier into the cabinet using four mounting screws (6-32 hex head
Phillips screws).
Note:If the floppy disk drive needs to be properly aligned with the front
bezel, loosen the mounting screws...

Page 110

CP 6222Remove/Install Floppy Disk DrivePage 1 of 5
VoiceMemo Release 6.OA and later
This procedure first describes how to remove and then how to install the floppy disk in
the Centigram Series 6 Model 70. It also describes how to remove and reinstall the drive
carrier. The drive carrier houses both the floppy disk drive and the hard disk. For
detailed floppy disk drive 
specifcations, see TR 192 1 in the Centigram Series G Technical
Reference Manual.
DANGER!Disconnect the server from its power source...
Start reading Mitel Voice Processing Solutions Installation And Service Manual

Related Manuals for Mitel Voice Processing Solutions Installation And Service Manual

All Mitel manuals