Mitel Voice Processing Solutions Installation And Service Manual

3 Upgrading and Updating SystemsHow To Use This ChapterThis chapter provides step-by-step procedures for upgrading and updating a Series 6
Model 
70. Additional information is also located in the VoiceMemo Reference and
Conjpration Manual and the Centigram Series G Technical Reference Manual.A task list and Centigram Procedures 
(CPs) describing upgrading and updating
procedures are located at the end of this chapter. The task list identifies two
procedural levels of 
CPs: a high-level CP and a low-level...

Upgrade and Update Task list
Page 1 of 1
VoiceMemo Release 6.OA and later
TaskProcedure
Upgrading and Updating Systems
ORline System Software Update. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Cl? 6483
InstallOptional Feature WithSystem Online...........................................Cl?5402
Perform anOfflinePrompts
Update........................................................
Cl?6262
Perform...

cp 5402
Install Optional Feature With System Online
Page 1 of 2
VoiceMemo Release 6.OA and later
The procedure describes how to install an optional feature with the system online. Be
sure the Optional Feature Diskette(s) and the Module Enable Diskette contain the serial
number(s) for all disk(s) in the system.
Note:The serial number on the OneView Optional Feature diskette must match the
serial number of the hard disk on which 
OneView is being installed.If you
receive an error message about an incorrect...

Cl? 5402
Page 2 of 2VoiceMemo Release 6.OA and later
StepReference
6.The following prompt appears:
Prompt: Wait for paging queues to be empty?Response: N to continue.
7.Exit to the VoiceMemo Configuration - Main Menu, then go to the VoiceMemoConfiguration 
- Offline Menu.
8.Duplicate the active configuration.
Select(B) Duplicate Active Configuration
9.Exit to the VoiceMemo Configuration -Main Menu and activate the configurat?on.
Select:(A) Activate Configuration
tienu Map 2 

cp 6262Perform an Offline Prompts Update
Page 1 of 3
VoiceMemo Release 6.OA and later
This procedure describes the offline process of updating the prompts on the Model 120
or Model 70.
FOR THE MODEL 120 AND MODEL 
70 ONLY: Some system prompts in this
procedure may contain generic references to other multiple-module Centigram Series 6
products. In such cases, shaded areas indicate a difference in operations for the Model
120 and Model 70. The Model 120 and Model 70 are equivalent to “one module”
servers....

SteDReference
CP 6262
Page 2 of 3
VoiceMemo Release 6.OA and later
5.Decide if you want to wait for paging queues to clear.
prompt: Wait for paging queues to be empty?
Response: Y to wait for the queue to clear,
N to continue immediately with the shutdown.
The following messages are then displayed:
Message Indicator Request Queue Lengths
active:0untried:0retrying:0calls expected:0
Paging Request Queue Lengths
I,
active:0untried:0retrying:0calls expected:0
6.Specify if changes to the status of each module...

Cl6262Page 3 of 3
VoiceMemo Release 6.OA and later
StepReference9.The server automatically boots to the Maintenance From Hard Disk Menu. Select
the prompts.add program.
Prompt: Enter one of the names:
Response: prompts-add
10. Load the prompts diskettes.Prompt:Insert the 1st diskette containing the prompts
and press return
Response: Insert Prompts Disk 1 then press Enter to continue.
h,pt, Wait until drive light is out, insert language
disc 
#l,hit CR when ready.
Response:Press Enter again to continue....

cp 6263Perform an Offline 
Sofbwre UpdatePage 1 of 5VoiceMemo Release 6.OA and later
This procedure describes how to update the software on a Model 120 or Model 70. It
applies only to Release 6.0 and above. To update software, the server must be shut
down and disabled using the procedure described in Cl? 6268.
FOR THE MODEL 120 AND MODEL 70 ONLY: Some system prompts in this
procedure may contain generic references to other multiple-module Centigram Series 6
products. In such cases, shaded areas indicate...

CP 6263
Page 2 of 5VoiceMemo Release 6.OA and later
step4.The server reads from the floppy disk and issues a warning about the pending
process.
J’rompt: WARNING! !******X*** UPDATE PROGRAM t*********UPDATE program ONLY updates the system
software files.
Data such as accounts,
and speech will remain unchanged (prompts
cleared later on UPDATE program only
if told so).
Any billing data files
constructed via the 
(G)ather command may
be incompatible with the new release. To be,
sure you will not lose...

CP 6263Page 3 of 5
VoiceMemo Release 6.OA and later
Step
6.If an old format of billing data is found on the server, the following message is
displayed:
Prompt: Old format of billing report data found.
This data
must be deleted before proceeding with the software
update.To run any billing reports from the last
gather,reboot the system now.Proceeding from here
will NOT result in any lost billing data provided
you have already run all needed reports from the
last gather. Note:
Future updates will not...