Mitel Voice Processing Solutions Installation And Service Manual

cl?5415Set the Site Name, Banner, and Code
Page 1 of 1
VoiceMemo Release 6.OA and later
This procedure describes how to set the site name, site banner, and the site code.
StepReference
1.Reach the System Maintenance Menu.
2.Change the site name.
Select:(N) System Name. Code, and Banner
Prompt: Enter ‘Y’ to change the site name, N to keep the
current site name:
/lenu MapIResponse: Y to change the name,
N to keep the current name.
3.If you answered yes to step 2, then enter the new site name, otherwise...

cl?5701Run Verify With System Offline
Page 1 of 3
VoiceMemo Release 6.OA and later
This procedure describes how to execute an offline system verify. The verify can be run
only if all modules are shut down. For information regarding online system verification,
see CP 700 1.FOR THE MODEL 120 AND MODEL 70 ONLY: Some system prompts in this
procedure may contain generic references to other multiple-module Centigram Series 6
products. In such cases, shaded areas indicate a difference in operations for the...

cl? 5701Page 2 of 3
VoiceMemo Release G.OA and later
Step6.When the verify is complete, the system continues with the shutdown, asking if the
server should wait while the message waiting indicators are updated.If any errors
were encountered during the verify, contact the Technical Assistance Center.
7.Change the status of the modules if desired.
Prompt:Enable or Disable Modules?Response: Y to change the status of modules,
N to keep the module status the same and continue at step 11.
8.Ifyou answered yes...

cl? 5701Page 3 of 3
VoiceMemo Release 6.OA and later
StepReference13. Review the Verify Report.
Select:(V) Verify
Prompt: Report destination:
Response: cIf any errors were recorded in the report, contact the Technical Assistance Center.
14. Exit to the Main Menu.
15. Turn off the system power or press the reset button(s) to reboot.
Dot. Rev. A 

Do a Floppy Backupcl? 5703Page 1 of 1
VoiceMemo Release 6.OA and later
This procedure describes how to perform a floppy backup of the Series 6 server.
step
1.Reach the System Maintenance Menu.
2.Initiate the floppy backup.
Select:(F) Floppy Backup
Prompt: Insert Backup Diskette 1 in floppy drive
Enter
Y when ready, or N to quit:
Response: Insert the diskette and enter Y to continue,
N to abort the backup process.
8.
3.If the diskette has not been formatted in QNX, format the diskette.
Prompt:Invalid...

cl? 5704Perform a System Restore (system.restore)
Page 1 of 3
VoiceMemo Release 6.OA and later
This procedure describes how to perform a system restore.
It is assumed the Series 6 server has been shut down and all modules disabled using the
process described in CP 6268.
WARNING!During this procedure, the server cannot process calls. Centigram
recommends that you run this process during periods of low call traffic.
Step
1.Boot the system. (All modules boot to the Maintenance From Hard Disk Meiu,since they...

CP 5704
Page 2 of 3
VoiceMemo Release 6.OA and later
StepReference6.If you answered yes to restoring the configuration and billing information, specify
the information to be restored; otherwise continue at step 8.
Prompt: Enter Yif you want to restore Billing rates
file:Response: Y to restore the information,
N to not restore the information.
Prompt: 
EnterY if you want to restore System name
file:Response: Y to restore the information,
N to not restore the information.
Prompt: Enter Yif you want to...

CP 5704
Page 3 of 3
VoiceMemo Release 6.OA and later
Step
7.If you answered yes to restoring the VoiceMemo configuration file, specify which
configuration is to be restored; otherwise continue at step 8.
h~~pt: EnterY if you want to restore VoiceMemo
configuration file 0:Response: Y to restore configuration file 0,
N to not restore configuration file 0.
PXIWZ~: EnterY if you want to restore VoiceMemo
configuration file 1:
Response: Y to restore configuration file 1,N to not restore configuration file 1....

cp 6267Reload a System 
(systemxeload)Page 1 of 5VoiceMemo Release 6.OA and later
This procedure describes how to install the software on an Model 
120 or Model 70
using the System Reload program. This program should be used only on a 
non-
redundant server that has experienced a disk failure, and only when you are instructed
to 
use it.Performing this procedure deletes the existing database of all speech, accounts,
and configuration. To update the server software and preserve the existing database of...

Cl’ 6267
Page 2 of 5
VoiceMemo Release 6.OA and later
Step
4.The server reads from the floppy disk, and issues a warning about the pending
process.
Proyqt: WARNING! !*****-k*** INSTALL PROGRAM ***-k-k*****INSTALL program should be executed only when a
complete system
installation
is desired (from scratch).
This means that
all information
on thesystem
(accounts,speech,
programs,etc.) will be
lost.
If you have a current
account backup diskette, the
account data
(but not speech) can be reloaded
via the...